What could be the reason, an AP has been taken as an inactive AP by V2110 version 9

  • 0
  • 1
  • Question
  • Updated 3 years ago
  • Answered
I'm a newbie for  APs.

I have connected an  AP 3825i  with V2110 version 09.21.
Controller indicates that this is an inactive AP.  I have given static IPs both AP and the controller in the same subnet (no DNS, no DHCP).  IPs can be pinged and  AP was approved by the controller.
I'm unable to view AP logs from the controller and  AP is not configurable using controller (only via SSH). 

What could be the possible reason for this ?  Thank you very much if somebody can advice me on this.


configuration of AP is as below. 

AP3825i 09.15.04.0011 interactive shell for service personnel only
# more /flash/home/config/current.cfg
version 5100
cset locaAddMac
cset authIpAddr 1 10.5.0.190
cset dhcpc disable
cset ipAddr 10.5.0.195
cset gateway 10.5.0.1
cset hostname EXNDEDRS02AP001
cset staticmtu 1300
cset apname 15240548085J0000
cset lbsMcast 00:00:00:00:00:00
cset ethernet speedDuplex auto
cset acMgmtMac 00:00:00:00:00:00
cset thirdPartyApMode disable

# radio 0
cset minBasicRate 0 6
# radio 1
cset minBasicRate 1 1
# radio 0 vns 1

# radio 0 vns 2

# radio 0 vns 3

# radio 0 vns 4

Photo of Weda

Weda

  • 994 Points 500 badge 2x thumb

Posted 3 years ago

  • 0
  • 1
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 47,434 Points 20k badge 2x thumb
Most possible reason ... configuration issue.

Please provide an screenshot of the controller that show the settings for the topology of 10.5.0.190.

-Ron
Photo of Doug Hyde

Doug Hyde, Technical Support Manager

  • 20,502 Points 20k badge 2x thumb
On the wireless appliance GUI select.... Controller--> (left side)Logs---> Select Wireless AP Log Level Informational, save it 
Check the Controller Logs and see if anything is showing up as to why it's failing to connect. 

Also is your physical controller topology port setup to allow AP Registration? 

Photo of Weda

Weda

  • 994 Points 500 badge 2x thumb
Log level had been set to Informational.
Admin interface and AP have Ips in same subnet. eg. 10.5.0.190 and 10.5.0.195

I'm using b@ap type interface for this AP and VLAN. Is that a bad option ?

Further more I tried to assign an IP of same subnet range 10.5.0.x . but it is not allowed.
What could I do in this case ?  Thank you very much in advance.
Photo of Doug Hyde

Doug Hyde, Technical Support Manager

  • 20,502 Points 20k badge 2x thumb
I would set the Admin port back to 192.168.10.1 and configure a physical ESA port with the address you currently have as your Admin port (see my screen shot above). 

Admin = Out of Band Management
Physical port= Management and AP Registration 

If you get locked out of the controller, console in and configure the controller as follows... 

EWC.extremenetworks.com# topology
EWC.extremenetworks.com: topology# create "Management" physical 1 port esa0 untag 10.26.0.166/20   (use your IP address this is an example) 
EWC.extremenetworks.com: topology# apply
EWC.extremenetworks.com: topology# Management
EWC.extremenetworks.com: topology: Management# l3
EWC.extremenetworks.com: topology: Management: l3# ap-register enable
EWC.extremenetworks.com: topology: Management: l3# mgmt enable
EWC.extremenetworks.com: topology: Management: l3# apply
EWC.extremenetworks.com: topology: Management: l3# exit
EWC.extremenetworks.com: topology: Management# exit
EWC.extremenetworks.com: topology# exit


If all else fails, contact the GTAC for assistance. 
Photo of Weda

Weda

  • 994 Points 500 badge 2x thumb
This worked out fine for my requirement. Thanks Doug.
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 47,434 Points 20k badge 2x thumb
You can't use the Admin/Mgmt interface to connect APs - this is not supported.
Photo of Weda

Weda

  • 994 Points 500 badge 2x thumb
Thanks for you reply... I'm wondering how I could do this as I have only IPs in 10.5.0.0/24 range. If you have a way to fix this with above resources, please let me know.  In addition, in which situations, B@AP is used?
Photo of Weda

Weda

  • 994 Points 500 badge 2x thumb
Sorry.. this question is not valid.. I saw Doug's reply later. My bad...
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 47,434 Points 20k badge 2x thumb
As Doug mentioned... configure the admin/mgmt port to another address (and don't use the port).
Add a new physical port with the 10.5.0.190 IP which you use for mgmt and AP registration.

bridge@AP is used if you want the client traffic to be bridged directly at the AP and not go via the controller.


I'd strongly recommend to attend the wireless class as without former experience it's very hard to configure everything correct / to unterstand how the system works.

http://www.extremenetworks.com/education/courses/ECS-HI-1-JS
http://www.extremenetworks.com/education/courses/ESE-HI-1