XOS command like EOS show ip interface ?


Userlevel 6
Exists in recent XOS firmware a commnd or commands which check the IP Parameters of a L3 Routing interface ?

Enterasys EOS does this the followin way:
Extreme B5
Chassis Firmware Revision: 06.81.05.0003[/code]sw-mg-eg(su)->router
sw-mg-eg(su)->router>show ip int
Vlan 2128 is Admin UP
Vlan 2128 is Oper UP
Primary IP Address is 172.16.128.186
Frame Type Ethernet
MAC-Address 20B3.99EC.7B0B
Incoming Accesslist is not set
MTU is 1500 bytes
ARP Timeout is 14400 seconds
Direct Broadcast Disabled
Proxy ARP is Disabled
sw-mg-eg(su)->[/code]

4 replies

Userlevel 4
Matthias,

The "show vlan" and "show vlan " commands can provide similar information within EXOS.

Andrew
Userlevel 7
Hi Matthias,

I believe 'show ipconfig' should show what you want. The example below is from an MLAG test setup I have in the lab.

swi2.1 # show ipconfig Use Redirects : Disabled IpOption LSRR : Enabled IpOption SSRR : Enabled IpOption RR : Enabled IpOption TS : Enabled IpOption RA : Enabled Route Sharing : Disabled Route Compression : Enabled Originated Packets : Don't require ipforwarding Max Shared Gateways : Current: 4 Configured: 4 Route Sharing Hash : CRC Lower
IRDP: Advertisement Address: 255.255.255.255 Maximum Interval: 600 Minimum Interval: 450 Lifetime: 1800 Preference: 0
Interface IP Address Flags nSIA isc 1.1.1.2 /30 EU----MPuRX--------- 0 v10 10.10.10.2 /24 EUf---MPuRX--------- 0 v11 11.11.11.2 /24 EUf---MPuRX--------- 0 v12 12.12.12.2 /24 EUf---MPuRX--------- 0 v13 13.13.13.2 /24 EUf---MPuRX--------- 0 v14 14.14.14.2 /24 EUf---MPuRX--------- 0 v15 15.15.15.2 /24 EUf---MPuRX--------- 0 v16 16.16.16.2 /24 EUf---MPuRX--------- 0 v17 17.17.17.2 /24 EUf---MPuRX--------- 0 v18 18.18.18.2 /24 EUf---MPuRX--------- 0 v19 19.19.19.2 /24 EUf---MPuRX--------- 0 v2 2.2.2.2 /24 EUf---MPuRX--------- 0 v20 20.20.20.2 /24 EUf---MPuRX--------- 0 v21 21.21.21.2 /24 EUf---MPuRX--------- 0 v22 22.22.22.2 /24 EUf---MPuRX--------- 0 v23 23.23.23.2 /24 EUf---MPuRX--------- 0 v24 24.24.24.2 /24 EUf---MPuRX--------- 0 v25 25.25.25.2 /24 EUf---MPuRX--------- 0 v26 26.26.26.2 /24 EUf---MPuRX--------- 0 v27 27.27.27.2 /24 EUf---MPuRX--------- 0 v28 28.28.28.2 /24 EUf---MPuRX--------- 0 v3 3.3.3.2 /24 EUf---MPuRX--------- 0 v4 4.4.4.2 /24 EUf---MPuRX--------- 0 v5 5.5.5.2 /24 EUf---MPuRX--------- 0 v6 6.6.6.2 /24 EUf---MPuRX--------- 0 v7 7.7.7.2 /24 EUf---MPuRX--------- 0 v8 8.8.8.2 /24 EUf---MPuRX--------- 0 v9 9.9.9.2 /24 EUf---MPuRX--------- 0
Flags: (A) Address Mask Reply Enabled (B) BOOTP Enabled (b) Broadcast Forwarding Enabled (D) Duplicate address detected on VLAN, (E) Interface Enabled (f) Forwarding Enabled (g) Ignore IP Broadcast Enabled (h) Directed Broadcast Forwarding by Hardware Enabled (I) IRDP Advertisement Enabled, (M) Send Parameter Problem Enabled (m) Multicast forwarding Enabled, (n) Multinetted VLAN (nSIA ) Number of Secondary IP Addresses (P) Send Port Unreachables Enabled, (R) Send Redirects Enabled (r) Unicast Reverse Path Enabled on at least one port of the VLAN (t) Tentative address, (T) Time Stamp Reply Enabled (u) Send Unreachables Enabled, (U) Interface Up (v) VRRP Enabled, (X) Send Time Exceeded Enabled
[/code]

-Brandon
Userlevel 6
Hi Brandon,
"show ipconfig" is the command which answer mostly my questions.
Thanks.

Do you know especially regarding ip proxy-arp - how to disable this on XOS ?

Regards
Userlevel 7
M.Nees wrote:

Hi Brandon,
"show ipconfig" is the command which answer mostly my questions.
Thanks.

Do you know especially regarding ip proxy-arp - how to disable this on XOS ?

Regards

There is no need to disable it, as EXOS will not do proxy ARP unless it is explicitly configured.

It can be set up for either specific addresses or an entire subnet.

-Brandon

Reply