Header Only - DO NOT REMOVE - Extreme Networks

EXOS 16.1.1 supports VLAN IDs (VID)s


Userlevel 5
Did you know ...
In EXOS 16.1.1, over 50 VLAN commands were enhanced to support VID lists/ranges to simplify configuration.

E.g. create vlan 10-20
Creates VLANs with the VIDs 10,11,12 etc...
EXOS still uses VLAN names internally so the VLAN names are created for you as VLAN_0010, VLAN_0011 etc ...

The list of commands below were all enhanced to accept which is the numeric VID form for VLANs.

A can be comma or dash separated numbers:

E.g.: 2,3,5-35 (VID 2,3 and all VIDs in the range of 5-35)

Here's the list of CLI commands that were enhanced.

code:

clear l2stats vlan

code:

configure ip-mtu vlan

code:

configure policy maptable [response [tunnel | policy | both] | ]

code:

configure policy profile {name } {pvid } {pvid-status } {cos } {cos-status } {egress-vlans } {forbidden-vlans } {untagged-vlans } {append | clear} {tci-overwrite } {precedence } {mirror-destination } {clear-mirror | prohibit-mirror | syslog } {trap } {disable-port } {fst } {web-redirect }

code:

configure ports [ | all] monitor vlan {rx-only | tx-only}

code:

configure ports {tagged} vlan [limit-learning { action [blackhole | stop-learning]} | unlimited-learning]

code:

configure ports {tagged} vlan [lock-learning | unlock-learning]

code:

configure {stpd} add vlan ports [all | ] {dot1d | emistp | pvst-plus}

code:

configure {stpd} delete vlan ports [all | ]

code:

configure vlan [ | ] add ports [all | ] {tagged | untagged} {stpd} {dot1d | emistp | pvst-plus}

code:

configure vlan [ | ] add ports [ | all] {tagged | untagged | private-vlan translated }

code:

configure vlan [ | ] delete ports [ | all]

code:

configure vlan [ | ] protocol {filter}

code:

configure vlan [ | ] {qosprofile} [ | none]

code:

configure vman [ | ] delete ports [ | all]

code:

configure vman [ | ] ports [ | all] delete cvid { - }

code:

configure vman [ | ] protocol {filter}

code:

configure vman [ | ] {qosprofile} [ | none]

code:

create vlan {vr } {description }

code:

create vman {vr } {description }

code:

delete vlan

code:

delete vman

code:

disable {stpd} auto-bind vlan

code:

[enable | disable] iparp gratuitous protect vlan

code:

[enable | disable] ipforwarding {ipv4} vlan

code:

[enable | disable] ipforwarding ipv6 vlan

code:

[enable | disable] learning [ vlan | vman ]

code:

[enable | disable] learning [ vlan | vman ]

code:

[enable | disable] loopback-mode vlan

code:

[enable | disable] vlan

code:

enable {stpd} auto-bind vlan

code:

show fdb stats vlan

code:

show fdb vlan {netlogin [all | mac-based-vlans]}

code:

show iparp security vlan

code:

show iparp stats vlan

code:

show iparp vlan

code:

show ip dad vlan {tentative | valid | duplicate}

code:

show ip-security arp learning vlan

code:

show ip-security arp validation violations vlan ports [|all]

code:

show ip-security arp validation vlan

code:

show ip-security dhcp-snooping entries vlan

code:

show ip-security dhcp-snooping information-option circuit-id vlan-information vlan

code:

show ip-security dhcp-snooping violations vlan

code:

show ip-security dhcp-snooping vlan

code:

show ipv6 dad vlan {tentative | valid | duplicate} {detail}

code:

show l2stats vlan

code:

show neighbor-discovery {cache {ipv6}} vlan

code:

show netlogin authentication [service-unavailable | failure] vlan

code:

show netlogin guest-vlan

code:

show netlogin {port } vlan

code:

show netlogin {port } vlan dot1x detail

code:

show policy maptable { }

code:

show vlan security

code:

show vlan statistics

code:

show vlan stpd {blocked-ports}

code:

show [vlan | vman ] {ipv4 | ipv6}

code:

show [vlan | vman ] {ipv4 | ipv6}

code:

show vrrp vlan {stats}

code:

unconfigure policy maptable [ response | ]

code:

unconfigure ports [ | all] monitor vlan

code:

unconfigure vlan ipaddress

code:

unconfigure vman ipaddress

2 replies

Awesome work, thanks Dave!
Userlevel 4
It's cool. Thanks!

Reply