Header Only - DO NOT REMOVE - Extreme Networks

Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.


Userlevel 1
My X460G2 was rebooted and upgraded to firmare version 22.1.1.5. This was intermittent about six hours. Then I rebooted again and its up. But can u help me?... What does this los´ mean?

03/06/2017 02:10:22.37 Slot-1: EPM Started
03/06/2017 02:10:22.36 Slot-1: Booting after System Failure.
03/06/2017 02:10:22.26 Slot-2: Booting after System Failure.
03/06/2017 02:10:22.18 Slot-3: Booting after System Failure.
03/06/2017 02:10:21.25 Slot-1: Changing to watchdog warm reset mode

thanks.!!

9 replies

Userlevel 6
Hello Angel,

Did you pull the plug on the switches?
Userlevel 1
Hi Patrick no I didn´t, just ther rebooted by itselve.
Userlevel 4
To me this is something found to be the switch lost power and this is either a power cable problem or the power supplying the switch went out throwing these log message later:

Slot-1: Booting after System Failure.
Userlevel 6
The fact that all 3 switches rebooted at the same time makes me believe that the power source needs to be looked into.
Userlevel 1
I found the problem, and yes affectively it was the power. Thanks a lot. One more cuestion.
What do you think about firmware version 22.1.1.5?
Do you know if this has some problems whith another versions?
Userlevel 7
Angel Pavon wrote:

I found the problem, and yes affectively it was the power. Thanks a lot. One more cuestion.
What do you think about firmware version 22.1.1.5?
Do you know if this has some problems whith another versions?

Angel, that release is very new and has not received any patches yet. There are a few issues with SSH that I believed are resolved in 22.2, but it also is quite new. That shouldn't be a deterrent, but rather something to consider. Check the release notes for each to review known issues.
Userlevel 2
Angel Pavon wrote:

I found the problem, and yes affectively it was the power. Thanks a lot. One more cuestion.
What do you think about firmware version 22.1.1.5?
Do you know if this has some problems whith another versions?

Please refer to the Release Notes below for 22.1 -
This EXOS version doesn't have the fix for the SSH issues: http://documentation.extremenetworks.com/release_notes/ExtremeXOS/22.1/downloads/ExtremeXOS_22.1_Rel...

Please refer to the Release Notes below for 22.2 -
This EXOS version contains the fix for the SSH issues: http://documentation.extremenetworks.com/release_notes/ExtremeXOS/22.2/downloads/ExtremeXOS_22.2_Rel...
Userlevel 1
Angel Pavon wrote:

I found the problem, and yes affectively it was the power. Thanks a lot. One more cuestion.
What do you think about firmware version 22.1.1.5?
Do you know if this has some problems whith another versions?

Thanks a lot!!!! Friends.
Angel Pavon wrote:

I found the problem, and yes affectively it was the power. Thanks a lot. One more cuestion.
What do you think about firmware version 22.1.1.5?
Do you know if this has some problems whith another versions?

Hi Angel,

I have the same problem, so what was your conclusion about the error. Did you change the power supply? power cord?

Thanks
Sylvain
Userlevel 4
As such to my understanding i do not think there are any other issues related to this firmware. Moreover with this 22.1.1.5 seems there are two patches available for now. patch2-2 and patch 4-1. Patch 4-1 being the latest one since feb 2017.

Hope this helps answering your queries.

Reply