How can i determine if maybe some cable or gbic problem exists on the stacking connections.
Regards
Best answer by M.Nees
At that time these Solution was created by GTAC:
https://extremeportal.force.com/ExtrArticleDetail?an=000080780
RX / TX Errors on alternate stacking ports
Userlevel 6
How can i request rx (and tx) errors on extreme (alternate) stacking port - escpecially 10Gb / 40GB ports. Standard "show port rxerrors" will not work because ports are in the Stacking mode and in currently indicated as NP (not present). "Show stacking stack-ports" does also not provide this information.
How can i determine if maybe some cable or gbic problem exists on the stacking connections.
Regards
How can i determine if maybe some cable or gbic problem exists on the stacking connections.
Regards
View original
Userlevel 1
- Extreme Employee
- 7 replies
-
21 March 2016
You can check rxerror/txerror in stacking ports by command
sh port stack-ports txerrors|rxerrors
sh port stack-ports txerrors|rxerrors
Userlevel 6
Perfect!! Thanks
Userlevel 6
Is it possible to get an alarm (syslog or trap) if command "show port stack-ports rxerrors" shows any errors ?
Maybe via CLEAR Flow / UPM / EXOS Scripting ?
Unfortunately this values are NOT able to monitor via SNMP!
Slot-1 DC-2-25.15 #
Slot-1 DC-2-25.15 # sh port stack-ports rxerrors no-refresh xerrors no-refresh txerrors no-refresh
Port Tx Error Monitor
Port Link Tx Tx Tx Tx Tx Tx
State Coll Late coll Deferred Errors Lost Parity
================================================================================
1:1 A 0 0 0 0 0 0
1:2 A 0 0 0 0 0 0
2:1 A 0 0 0 0 0 0
2:2 A 0 0 0 0 0 0
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present L-Loopback
Slot-1 DC-2-25.16 #
Slot-1 DC-2-25.16 # [/code]Regards
Maybe via CLEAR Flow / UPM / EXOS Scripting ?
Unfortunately this values are NOT able to monitor via SNMP!
Slot-1 DC-2-25.15 #
Slot-1 DC-2-25.15 # sh port stack-ports rxerrors no-refresh xerrors no-refresh txerrors no-refresh
Port Tx Error Monitor
Port Link Tx Tx Tx Tx Tx Tx
State Coll Late coll Deferred Errors Lost Parity
================================================================================
1:1 A 0 0 0 0 0 0
1:2 A 0 0 0 0 0 0
2:1 A 0 0 0 0 0 0
2:2 A 0 0 0 0 0 0
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present L-Loopback
Slot-1 DC-2-25.16 #
Slot-1 DC-2-25.16 # [/code]Regards
Userlevel 6
No advice how i can automatically monitor errrors on stackports ?
Userlevel 6
i opened a GTAC Case for this - now i have a feedback!
Unfortunately there is no EMS Event to trigger an event NOR you can read out this values via SNMP!
So i create a Feature Request to have this (maybe) in the near future.
Regards
Unfortunately there is no EMS Event to trigger an event NOR you can read out this values via SNMP!
So i create a Feature Request to have this (maybe) in the near future.
Regards
Userlevel 6
At that time these Solution was created by GTAC:
https://extremeportal.force.com/ExtrArticleDetail?an=000080780
Reply
Enter your username or e-mail address. We'll send you an e-mail with instructions to reset your password.