Hello,
I'm curious if 802.11k/Beacon Report/Quiet IE are recommended on C5210 running 10.11.x. If so, will they impact performance/air usage at all?
I'm curious about the "nearby AP's" report, which requires 11k in order to view.
Extreme Networks
-
Solutions
Discover how Extreme Elements enable the Autonomous Enterprise.
- Products
- Services
- Support
- Resources
- Blog
Userlevel 1
- Extreme Hero
- 33 replies
-
21 September 2016
Hi Joshua,
you can run 802.1k/Beacon Report/Quit IE without any performance issues on a C5210. I totally recommend the use of 802.11k, because it is needed e.g. for the Nearby AP Report. Through 802.11k your APs will have a better "understanding" of what is going on and what is around.
Regards,
Philipp
you can run 802.1k/Beacon Report/Quit IE without any performance issues on a C5210. I totally recommend the use of 802.11k, because it is needed e.g. for the Nearby AP Report. Through 802.11k your APs will have a better "understanding" of what is going on and what is around.
Regards,
Philipp
Userlevel 6
I'm running 802.11k on 9.21.12 and 10.11.02. There were some crashing problems with AP3825 but they've all been fixed. Also note that enabling with disconnect all clients from the VNS.
Does anyone know what Beacon Report and Quiet IE actually do? The help page is pretty minimal.
Does anyone know what Beacon Report and Quiet IE actually do? The help page is pretty minimal.
Userlevel 3
- Extreme Employee
- 33 replies
-
2 December 2016
Adding to the information already posted above, the 'Nearby AP Report' is a very useful report in understanding roaming options and signal strength of such APs in a WLAN.
- Extreme Employee
- 22 replies
-
1 December 2016
Hi James
Greetings
IE - Information Element could be seen only on Management Frames
Quiet IE
Dynamic frequency selection was needed to avoid certain military radar technologies.To find the presence of radar or other interference,an AP can use the Quiet element to temporarily shut down the channel to improve the quality of measurements.
Beacon Report
The 802.11k protocol allows APs and clients to dynamically measure the available radio resources.The APs and clients can send neighbor reports, beacon reports and link measurement reports to each other.
This allows the APs and clients to take appropriate connection actions like band-steer,move sticky client.
The beacon report requests are sent only to 802.11k-compliant clients that advertise Beacon Report Capability in their RRM Enabled Capabilities IE
Client's 11k Beacon Report to AP
-----------------------------------
BSSID Channel RSSI
ff:ff:ff:b6:62:f0 38 92
ff:ff:ff:b6:69:30 38 94
ff:ff:ff:4a:43:d0 46 94
ff:ff:ff:b6:66:30 46 92
Regards
Rajesh J
Greetings
IE - Information Element could be seen only on Management Frames
Quiet IE
Dynamic frequency selection was needed to avoid certain military radar technologies.To find the presence of radar or other interference,an AP can use the Quiet element to temporarily shut down the channel to improve the quality of measurements.
Beacon Report
The 802.11k protocol allows APs and clients to dynamically measure the available radio resources.The APs and clients can send neighbor reports, beacon reports and link measurement reports to each other.
This allows the APs and clients to take appropriate connection actions like band-steer,move sticky client.
The beacon report requests are sent only to 802.11k-compliant clients that advertise Beacon Report Capability in their RRM Enabled Capabilities IE
Client's 11k Beacon Report to AP
-----------------------------------
BSSID Channel RSSI
ff:ff:ff:b6:62:f0 38 92
ff:ff:ff:b6:69:30 38 94
ff:ff:ff:4a:43:d0 46 94
ff:ff:ff:b6:66:30 46 92
Regards
Rajesh J
Reply
Enter your username or e-mail address to receive an e-mail with instructions to reset your password.