mobility tunnel


Userlevel 1
I have two controllers WC-35 with version 10.31.01.0048, and C4110 with version 09.21.10.0005, and i would like configure mobility tunnel between tow controllers, the controller´s dont have HA, this is possible?

14 replies

Userlevel 7
Yes
Userlevel 1
But is necessary create a HA?
Userlevel 5
Hello Salvador,

you don't need HA!

Regards
Stephan
Userlevel 1
SH wrote:

Hello Salvador,

you don't need HA!

Regards
Stephan

i tryed and the tunnel does not up, i have differents segment of network on interface of register 10.10.1.0/24 and 10.10.3.0/24. is necesary that the inferfaces have the same network segment?
Userlevel 7
SH wrote:

Hello Salvador,

you don't need HA!

Regards
Stephan

No, they don't need to be on the same VLAN/subnet.

Is a route configured on the controller so they could reach each other - you could try a ping from controller#1 to controller#2 to see whether routing works.
Userlevel 5
Mybe there is a firewall between your networks?
Visit the release notes for the necessary ports.
Userlevel 1
The two controllers are in the same LAN conect at the core
Userlevel 5
Are you using NTP and do you have the same time on both controllers?
What do you see in the Reports->Mobility->Mobility Tunnel Matrix?
What do you see in the Logs for Mobility?
Userlevel 4
I assume but if not..add the mobility agents statically in the list?
Userlevel 1
i cal see this logs:
manager: Mobility tunnel establishment failed with Peer 10.15.2.254. Please verify peer's reachability
agent: Mobility tunnels with Peers reset due to membership credentials change on current controller
Userlevel 7
I'm sorry but it's hard to help if you don't provide exact information.....

1) what is the IP of controller#1&2 interface that you'd like to use for mobility and how are the interface topologies are configured = physical or bridge@EWC

2) could you ping the IP this IP from controller#1 and vice-versa
Userlevel 1
Ron wrote:

I'm sorry but it's hard to help if you don't provide exact information.....

1) what is the IP of controller#1&2 interface that you'd like to use for mobility and how are the interface topologies are configured = physical or bridge@EWC

2) could you ping the IP this IP from controller#1 and vice-versa

this is the information of controllers:

controller 1: interface physical 10.10.2.254/ 24 with Ap registrering, version 09.21.10.0005
controller 2: interface physical 10.10.3.254/ 24 with Ap registrering, version 10.31.01.0048

and ping is successfull in both directions.

but controller 1 have 61 VNS configured and other controller have 3 VNS.
Userlevel 7
Ron wrote:

I'm sorry but it's hard to help if you don't provide exact information.....

1) what is the IP of controller#1&2 interface that you'd like to use for mobility and how are the interface topologies are configured = physical or bridge@EWC

2) could you ping the IP this IP from controller#1 and vice-versa

That IPs don't match with the IPs in the error message that you've provided...

"manager: Mobility tunnel establishment failed with Peer 10.15.2.254."
Userlevel 1
Ron wrote:

I'm sorry but it's hard to help if you don't provide exact information.....

1) what is the IP of controller#1&2 interface that you'd like to use for mobility and how are the interface topologies are configured = physical or bridge@EWC

2) could you ping the IP this IP from controller#1 and vice-versa

sorry, the Second octet is 15 for both segment of network, 10.15.2.254/24 and 10.15.3.254/24

Reply