Where is "RSS Threshold" or similar on the 7532 ap

  • 23 February 2018
  • 9 replies
  • 380 views

Hello guys,

I would like to know where I find the "RSS Threshold" or similar on the RF domain profile of 7532 ap?

It has some document of better configurations for an environment with more than 50 7532 ap with rfs 6000 controller.

9 replies


Hello Ondrej,

Thanks for the answer!!!

Now I would like to know how to configure so that when a client is on an AP with the signal smaller than -70 it is disconnected or pass to another AP with a better signal?
Hi Elias,

use roaming assistance policy then

VX(config)# roaming-assist-policy RSSIVX(config-roaming-assist-policy-RSSI)# handoff-threshold <-100--40> RSSI
VX(config)# wlan RSSIVX(config-wlan-RSSI)# use roaming-assist-policy RSSI Make sure though, you have some "room" for roaming overlap.
Confirm with client RF statistics

VX# show wireless client statistics rf on
Regards,
Ondrej


Hi @Ondrej Lepa

CLI: handoff-threshold <-100--40

Means the threshold of RSSI -40 to -100dbm right?. If i need signal smaller than -75dbm it is disconnected or pass to another AP with a better signal i set CLI to
VX(config-roaming-assist-policy-RSSI)# handoff-threshold <-75--40> RSSI

I'm doing right?
Hi @Ondrej Lepa

Can you direct me to configure roaming-assist-policy RSSI the GUI interface?


Hello @Tuan Nguyen,

The @Ondrej Lepa in some posts above, informs that only via CLI configuration is possible.
Hi @Ondrej Lepa

Can you direct me to configure roaming-assist-policy RSSI the GUI interface?

Hello Ondrej,

Thanks for the answer!!!

Now I would like to know how to configure so that when a client is on an AP with the signal smaller than -70 it is disconnected or pass to another AP with a better signal?
Ok Ondrej,

Thanks for your help!!! 😃
Userlevel 6
Hello Ondrej,

Thanks for the answer!!!

Now I would like to know how to configure so that when a client is on an AP with the signal smaller than -70 it is disconnected or pass to another AP with a better signal?
Hi Elias,

I bet this is something you can configure only using CLI.

Regards,
Ondrej
Hello Ondrej,

Thanks for the answer!!!

Now I would like to know how to configure so that when a client is on an AP with the signal smaller than -70 it is disconnected or pass to another AP with a better signal?
Hi Ondrej,

I searched the options via wegui but did not find it. Can I make these settings via wegui, or only via terminal?
Userlevel 6
Hello Ondrej,

Thanks for the answer!!!

Now I would like to know how to configure so that when a client is on an AP with the signal smaller than -70 it is disconnected or pass to another AP with a better signal?
Hi Elias,

use roaming assistance policy then

VX(config)# roaming-assist-policy RSSI
VX(config-roaming-assist-policy-RSSI)# handoff-threshold <-100--40> RSSI
VX(config)# wlan RSSI
VX(config-wlan-RSSI)# use roaming-assist-policy RSSI

Make sure though, you have some "room" for roaming overlap.
Confirm with client RF statistics

VX# show wireless client statistics rf on

Regards,
Ondrej
Hello Ondrej,

Thanks for the answer!!!

Now I would like to know how to configure so that when a client is on an AP with the signal smaller than -70 it is disconnected or pass to another AP with a better signal?
Userlevel 6
Hello Elias,

do you mean something like this?
VX# show wireless radio statistics rf on [/code]



Regards,
Ondrej

Reply