topic Hello, I have bought an AP 130 unit 01301710160029. When I start it , it stay amber fix. I have console access. I see a DHCP request and give an IP but nothing more after. Is there a way to help me? in Aerohive Migrated Content

Hello, I have bought an AP 130 unit 01301710160029. When I start it , it stay amber fix. I have console access. I see a DHCP request and give an IP but nothing more after. Is there a way to help me?

johan1 — Tue, 25 Feb 2020 02:12:39 GMT

U-Boot 2012.10 (Aug 05 2019 - 20:48:35)

I2C: ready

Wait.

Done.

DEV ID= 0000cf12

REV ID= 00000000

SKU ID = 2

OTP status: eca01028

MEMC 0 DDR speed = 533MHz

Log: ddr40_phy_init.c: Configuring DDR Controller PLLs

Log: offset = 0x18010800

Log: VCO_FREQ is 1066 which is greater than 1Ghz.

Log: DDR Phy PLL polling for lock

Log: DDR Phy PLL locked.

Log: ddr40_phy_init::DDR PHY step size calibration complete.

Log: ddr40_phy_init:: Virtual VttSetup onm CONNECT=0x01CF7FFF, OVERRIDE=0x00077FFF

Log: ddr40_phy_init:: Virtual Vtt Enabled

Log: DDR Controller PLL Configuration Complete

PHY register dump after DDR PHY init

PHY register dump after mode register write

DRAM: 256 MiB

WARNING: Caches not enabled

GPIO Init ... Done

NAND: NAND_FLASH_DEVICE_ID_ADDR = 18028194

Done that

(ONFI), W29N04GV, blocks per lun: 1000 lun count: 1

*WARNING* Invalid strap options for this NAND: page=1 type=2

Overriding invalid strap options: strap_type=2

128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit

NAND: chipsize

total 0 bad blocks,LIST:

now the up level will see a good flash chip no bad block which size is 20000000

before nvram partition, there are 0 bad blocks

512 MiB

Using default environment

In: serial

Out: serial

Err: serial

Unlocking L2 Cache ...Done

arm_clk=800MHz, axi_clk=400MHz, apb_clk=200MHz, arm_periph_clk=400MHz

Net: Registering eth

Broadcom BCM IPROC Ethernet driver 0.1

Using GMAC1 (0x18025000)

et0: ethHw_chipAttach: Chip ID: 0xcf12; phyaddr: 0x1e

bcm_robo_attach: devid: 0x53011

bcmiproc_eth-0

MAC address is c867:5e4a:5e80

NVRAM_MAGIC found at offset 440000

nvram_init: ret 1

Reset TPM chip...

Reset AUTH chip...

Hit any key to stop autoboot: 0

Loading kernel from device 0: nand0 (offset 0x580000) ... done

Loading rootfs from device 0: nand0 (offset 0xf80000) ... done

## Booting kernel from Legacy Image at 01005000 ...

Image Name: Linux-3.16.36

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 2479437 Bytes = 2.4 MiB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ... OK

## Loading init Ramdisk from Legacy Image at 02005000 ...

Image Name: uboot initramfs rootfs

Image Type: ARM Linux RAMDisk Image (uncompressed)

Data Size: 28565504 Bytes = 27.2 MiB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

Power off two PHY...

Loading Kernel Image ... OK

boot_prep_linux commandline: root=/dev/ram console=ttyS0,9600 ramdisk_size=70000 cache-sram-size=0x10000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

L2C: platform provided aux values match the hardware, so have no effect. Please remove them.

L2C: platform provided aux values permit register corruption.

Mounting local file systems...

Do the DB init,please wait...

jffs2: notice: (60) check_node_data: wrong data CRC in data node at 0x137927a0: read 0x7854a223, calculated 0x722a6e35.

ah_net: module license 'unspecified' taints kernel.

Disabling lock debugging due to kernel taint

Updating system config database...

System config update complete.

gmac_var_init: NAPI2_POLL mode

Jumbo disabled

eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 10.10.80.505_e5.1.2.3 (r659762)

Jumbo disabled

Aerohive Wireless Extension 2.0.0 ... INIT!

Aerohive Forwarding Engine module ... INIT!

Image L7 repository version 5, checking existing L7 repository... ...

Existing L7 repository version 5

Nothing to be done or verified with L7 repository version 5

kddr enable

Welcome to Aerohive Product

Learning Support login:

Re: Hello, I have bought an AP 130 unit 01301710160029. When I start it , it stay amber fix. I have console access. I see a DHCP request and give an IP but nothing more after. Is there a way to help me?

ashley_finch — Tue, 25 Feb 2020 18:00:33 GMT

Have you got a hivemanager/CloudIQ account? If so I'd follow this guide to get it connected:

https://thehivecommunity.aerohive.com/s/article/CAPWAP-Guide-for-HiveManager-NG

Re: Hello, I have bought an AP 130 unit 01301710160029. When I start it , it stay amber fix. I have console access. I see a DHCP request and give an IP but nothing more after. Is there a way to help me?

johan1 — Tue, 25 Feb 2020 18:55:26 GMT

Hello

Yesterday I use an IQ cloud account with no 30 days test. Just free portal.
System stop at fix amber led at each time. I test reset hardware, let 2 hours connected for upgrade, reboot, etc…
Nothing append.

Today, I have create a new portal account with 30 days testing.
And now after 5 minutes, the hardware is connected with white LED and apply my local Policy.
[cid:image004.png@01D5EBCE.97190F90]

Is there a difference between the trial cloud and free cloud (after 30 days) for onboarding ?
In the free cloud account, I have 3 AP130 with firmware 6.5. In ne new try cloud account only this unit.

For finishing my test:

* I remove AP130 from the trial cloud account
* I connect to the free cloud account, I had the unit

* It became white after 2 minutes
* I see it into the cloud console
* The system reboot 2 times
* It became white now
* It works

So I don’t understand why I have “unlock” the product by adding it to a trial cloud portal and be able to come back to standard portal.

Anyway, it works. Sorry for my question.

Best regards
Johan DEVELON

Re: Hello, I have bought an AP 130 unit 01301710160029. When I start it , it stay amber fix. I have console access. I see a DHCP request and give an IP but nothing more after. Is there a way to help me?

ashley_finch — Tue, 25 Feb 2020 19:02:10 GMT

Hello,

There may be a difference in which server you connect to (IP wise) but otherwise there shouldn't be a difference I don't think. Glad you got it working though.