topic VDX 6730 Boot issues in Data Center (VDX)

VDX 6730 Boot issues

techlabstoi — Mon, 29 Jul 2019 05:10:16 GMT

Hey There,

i work for the IT School of our local institute and we have just received an ex-production Brocade VDX 6730 from our corporate IT Team to play with.

when i go to power it on the fans serge and the message "The system is coming up, please wait..." is displayed over and over on in the terminal.
so far today this have been going on for over an hour.

my question is how long should this system take to boot, and are we able to do some sort of hardware reset?

Thanks in advance

Re: VDX 6730 Boot issues

Truyen_Phan — Mon, 29 Jul 2019 05:17:25 GMT

Hello,

It should take about 7-11 mins to fully boot. It sounds like the switch is in a boot loop. Can you capture the console boot log and attach it here for us to check it further?

Re: VDX 6730 Boot issues

techlabstoi — Mon, 29 Jul 2019 05:39:19 GMT

Morning Truyen,

i booted up about 30 min ago, it took between 5-10 mins to show anything on the console port and since then it's been displaying this over and over again:

The system is coming up, please wait...

The system is coming up, please wait...
þ
The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The
The system is coming up, pleasý
þ
The system is coming up, please wait...

The systeÿ
The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, p
The systeí
The system is coming up, please wait...

The system is coming up, please ÷
The system ió
The ó
The system is coming up, please wait...

The system is cominç
The system is coming up, please wait...

The system i
The system is coming up, please wait...

The system is coming up, please wait...

The sý
The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

Tè
The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

The system is coming uþ
The system is coming up, please wait...

The system is coming up,
The system is coming up, please wait...

The system is coming up, please wait...

The system is coming up, please wait...

regards

sam

Re: VDX 6730 Boot issues

Truyen_Phan — Mon, 29 Jul 2019 06:28:49 GMT

Hi Sam,

Can you check the console to verify there are no issues with console connectivity? Perhaps try a different rolled cable or DB9 connector?

Normally, after the "The system is coming up, please wait..." message, it should boot into a uboot sequence which will allow you to stop the boot and do recovery on it.

If the console is correct and you don't see the Uboot coming up like below, then it's a hardware issue that needs to be replaced.

code:

The system is coming up, please wait...

U-Boot 2010.06 (Aug 12 2016 - 15:54:09)


CPU:   8548, Version: 2.1, (0x80310021)
Core:  E500, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU0:1200 MHz,
       CCB:400  MHz,
       DDR:200  MHz (400 MT/s data rate), LBC:50   MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Model ID: 0x8049
Board: 8548 ELARA2E
I2C:   ready
DRAM:  Initializing....
    DDR: 2 GiB (DDR2, 64-bit, CL=3, ECC on)
POST RAM test disabled.
Now running in RAM - U-Boot at: 7ffa0000
FLASH: 4 MiB
L2:    512 KB enabled
CPLD: Init complete
ATA interface setup upm 256: ffdfc04, fffffc01, fffffc00, fffffc00
PCI: gd->brcd_flags = 0, PCI init
    PCI1 connected to Slot 1 as host (base addr f7008000)
               Scanning PCI bus 00
        00  10  1657  0010  0280  1a
        00  14  1131  1561  0c03  1a
        00  14  1131  1562  0c03  1a
    PCIE1 on bus 00 - 00


    PCIE3 connected to Slot 3 as Root Complex (base addr f700a000)
               Scanning PCI bus 02
        04  00  1657  001a  0280  3c
        03  01  10b5  8508  0604  1a
        03  02  10b5  8508  0604  1a
        03  03  10b5  8508  0604  1a
        03  04  10b5  8508  0604  1a
        02  00  10b5  8508  0604  1a
    PCIE1 on bus 01 - 07


In:    serial
Out:   serial
Err:   serial
Net:   eTSEC0, eTSEC1
set_bootstatus: BS_LOAD_OS, platform_index = 0
Hit ESC to stop autoboot:  0


1) Start system.
2) Recover password.
3) Enter command shell.


Option?