Aerohive AP130 does not startup and hangs at "Mounting local file systems

Ecklb — Fri, 17 Nov 2023 09:05:02 GMT

hi, my aerohive ap130 needs to start up more than 1 hour, it hangs at boot "mounting local file systems"

i tried to do a hard reset but does not work,

i also cannot update the device or reset by IQ cloud

Re: Aerohive AP130 does not startup and hangs at "Mounting local file systems

Ecklb — Fri, 17 Nov 2023 09:11:16 GMT

cli

U-Boot 2012.10 (Dec 06 2021 - 11:23:44)

I2C: ready
Wait.
Done.
DEV ID= 0000cf12
REV ID= 00000000
SKU ID = 2
OTP status: eca01028
MEMC 0 DDR speed = 533MHz
Log: ddr40_phy_init.c: Configuring DDR Controller PLLs
Log: offset = 0x18010800
Log: VCO_FREQ is 1066 which is greater than 1Ghz.
Log: DDR Phy PLL polling for lock
Log: DDR Phy PLL locked.
Log: ddr40_phy_init::DDR PHY step size calibration complete.
Log: ddr40_phy_init:: Virtual VttSetup onm CONNECT=0x01CF7FFF, OVERRIDE=0x00077FFF
Log: ddr40_phy_init:: Virtual Vtt Enabled
Log: DDR Controller PLL Configuration Complete
PHY register dump after DDR PHY init
PHY register dump after mode register write
DRAM: 256 MiB
WARNING: Caches not enabled
GPIO Init ... Done
NAND: NAND_FLASH_DEVICE_ID_ADDR = 18028194
Done that
(ONFI), W29N04GV, blocks per lun: 1000 lun count: 1

*WARNING* Invalid strap options for this NAND: page=1 type=2
Overriding invalid strap options: strap_type=2
128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND: chipsize
total 0 bad blocks,LIST:
now the up level will see a good flash chip no bad block which size is 20000000
before nvram partition, there are 0 bad blocks
512 MiB
Using default environment

In: serial
Out: serial
Err: serial
Unlocking L2 Cache ...Done
arm_clk=800MHz, axi_clk=400MHz, apb_clk=200MHz, arm_periph_clk=400MHz
Net: Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC1 (0x18025000)
et0: ethHw_chipAttach: Chip ID: 0xcf12; phyaddr: 0x1e
bcm_robo_attach: devid: 0x53011
bcmiproc_eth-0
MAC address is c867:5e46:4140

NVRAM_MAGIC found at offset 440000
nvram_init: ret 1
Reset TPM chip...
Reset AUTH chip...
Hit any key to stop autoboot: 0

Loading kernel from device 0: nand0 (offset 0x580000) ... done
Loading rootfs from device 0: nand0 (offset 0xf80000) ... done
## Booting kernel from Legacy Image at 01005000 ...
Image Name: Linux-3.16.36
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2480365 Bytes = 2.4 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02005000 ...
Image Name: uboot initramfs rootfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 29507584 Bytes = 28.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Power off two PHY...
Loading Kernel Image ... OK
OK
boot_prep_linux commandline: root=/dev/ram console=ttyS0,9600 ramdisk_size=70000 cache-sram-size=0x10000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
L2C: platform provided aux values match the hardware, so have no effect. Please remove them.
L2C: platform provided aux values permit register corruption.
Mounting local file systems...
Do the DB init,please wait...
ah_net: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
jffs2: notice: (60) check_node_data: wrong data CRC in data node at 0x14184b20: read 0xb7a410bd, calculated 0x7f9b3719.
Updating system config database...
System config update complete.
gmac_var_init: NAPI2_POLL mode
Jumbo disabled
Jumbo disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 10.10.80.505_e5.1.2.3 (r659762)
register sniffer device on interface eth0.
Found radio: bus 1 slot 0 vendor 14e4 device 4360 irq 163
Found radio: bus 1 slot 0 vendor 14e4 device 4360 irq 169
Jumbo disabled
Jumbo disabled
Extreme Wireless Extension 2.0.0 ... INIT!
Extreme Forwarding Engine module ... INIT!
Image L7 repository version 5, checking existing L7 repository... ...
Existing L7 repository version 5
Nothing to be done or verified with L7 repository version 5

Welcome to Extreme Networks Product

AH-464140 login: admin
Password:
Copyright (c) 2006-2021 Extreme Networks, Inc.
AH-464140#

Re: Aerohive AP130 does not startup and hangs at "Mounting local file systems

Christoph_S — Fri, 17 Nov 2023 14:18:03 GMT

Hello Ecklb,

From what I understand, the AP takes a very long time to complete the boot process, is the accurate?

Once it does complete the boot process and you are able to log in, please run the following commands:

#show cpu detail

#show system process state

Press "C" to show each CPU utilization.

Do you have high CPU utilization and is a process hogging up the AP resources?

BR,

topic Re: Aerohive AP130 does not startup and hangs at "Mounting local file systems in ExtremeCloud IQ

Aerohive AP130 does not startup and hangs at "Mounting local file systems

Re: Aerohive AP130 does not startup and hangs at "Mounting local file systems

Re: Aerohive AP130 does not startup and hangs at "Mounting local file systems