<?xml version="1.0" encoding="UTF-8"?>
<rss xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#" xmlns:taxo="http://purl.org/rss/1.0/modules/taxonomy/" version="2.0">
  <channel>
    <title>topic Valid packet (%) in ExtremeCloud IQ- Site Engine Management Center</title>
    <link>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36078#M4146</link>
    <description>Does anyone know what the Valid packet (%) is based on when looking into the Top 100 Interfaces by bandwidth in Netsight? I can't seem to correlate that number to anything on the switch.&lt;BR /&gt;
&lt;BR /&gt;
I found this in the Manual:&lt;BR /&gt;
Errors&lt;BR /&gt;
If you choose the Errors mode, the interface boxes will display the percentage of&lt;BR /&gt;
the total number of valid packets processed by each port during the last polling&lt;BR /&gt;
interval that were error packets. This percentage reﬂects the number of errors&lt;BR /&gt;
generated during the last polling interval by devices connected to that port&lt;BR /&gt;
compared to the total number of valid packets processed by the port.&lt;BR /&gt;
&lt;BR /&gt;
But I don't see any errors on the switch port (ingress or egress), or the downstream switch, but the report shows 95% "Valid Packets (%)".&lt;BR /&gt;
&lt;BR /&gt;</description>
    <pubDate>Tue, 04 Aug 2015 21:25:00 GMT</pubDate>
    <dc:creator>craymond</dc:creator>
    <dc:date>2015-08-04T21:25:00Z</dc:date>
    <item>
      <title>Valid packet (%)</title>
      <link>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36078#M4146</link>
      <description>Does anyone know what the Valid packet (%) is based on when looking into the Top 100 Interfaces by bandwidth in Netsight? I can't seem to correlate that number to anything on the switch.&lt;BR /&gt;
&lt;BR /&gt;
I found this in the Manual:&lt;BR /&gt;
Errors&lt;BR /&gt;
If you choose the Errors mode, the interface boxes will display the percentage of&lt;BR /&gt;
the total number of valid packets processed by each port during the last polling&lt;BR /&gt;
interval that were error packets. This percentage reﬂects the number of errors&lt;BR /&gt;
generated during the last polling interval by devices connected to that port&lt;BR /&gt;
compared to the total number of valid packets processed by the port.&lt;BR /&gt;
&lt;BR /&gt;
But I don't see any errors on the switch port (ingress or egress), or the downstream switch, but the report shows 95% "Valid Packets (%)".&lt;BR /&gt;
&lt;BR /&gt;</description>
      <pubDate>Tue, 04 Aug 2015 21:25:00 GMT</pubDate>
      <guid>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36078#M4146</guid>
      <dc:creator>craymond</dc:creator>
      <dc:date>2015-08-04T21:25:00Z</dc:date>
    </item>
    <item>
      <title>RE: Valid packet (%)</title>
      <link>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36079#M4147</link>
      <description>Hi,&lt;BR /&gt;
If you question is about OneView interface Historical Collection&lt;BR /&gt;
&lt;BR /&gt;
Then percent is based on 'delta' interface packet counts from the MIB-II interface table&lt;BR /&gt;
&lt;BR /&gt;
% Error Packets = (error packets / (error packets + valid packets)) * 100&lt;BR /&gt;
% Valid Packets = (valid packets / (error packets + valid packets)) * 100&lt;BR /&gt;
&lt;BR /&gt;
For details look at OneView - Administration - Historical Statistic Collector &lt;BR /&gt;
Set Level: (to Advanced or Diagnostic) not Basic&lt;BR /&gt;
&lt;BR /&gt;
select--&amp;gt; Statistics &lt;BR /&gt;
&lt;BR /&gt;
Interface % Error Packets. Source: ifInDiscards + ifOutDiscards + ifInErrors + ifOutErrors + ifInUnknownProtos&lt;BR /&gt;
Interface % Utilization. Source (SNMPv1): ifInOctets and ifOutOctetsSource (SNMPv2c/v2): ifInHCOctets and ifHCOutOctets&lt;BR /&gt;
Interface % Valid Packets. Source (SNMPv1): ifInUcastPkts + ifInNUcastPkts + ifOutUcastPkts + ifOutNUcastPkts Source (SNMPv2c/v3): ifHCInUcastPkts + ifHCOutNUca&lt;BR /&gt;
&lt;BR /&gt;</description>
      <pubDate>Tue, 04 Aug 2015 22:09:00 GMT</pubDate>
      <guid>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36079#M4147</guid>
      <dc:creator>Murphy__Daniel</dc:creator>
      <dc:date>2015-08-04T22:09:00Z</dc:date>
    </item>
    <item>
      <title>RE: Valid packet (%)</title>
      <link>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36080#M4148</link>
      <description>So - the only way to see this is though SNMP, not from the CLI? I don't have any CRC errors or any others that I can see. Is there a way to figure out what the errors are?  Wireshark or similar?&lt;BR /&gt;
&lt;BR /&gt;</description>
      <pubDate>Tue, 04 Aug 2015 22:41:00 GMT</pubDate>
      <guid>https://community.extremenetworks.com/t5/extremecloud-iq-site-engine/valid-packet/m-p/36080#M4148</guid>
      <dc:creator>craymond</dc:creator>
      <dc:date>2015-08-04T22:41:00Z</dc:date>
    </item>
  </channel>
</rss>

