topic RE: initial setup x250e in ExtremeSwitching (EOS)

initial setup x250e

Benzion_Nussbau — Wed, 02 Aug 2017 09:38:00 GMT

I just got hold of a few extreme x250e and I would like to use them to power a camera system that I have ( I am a cisco guy but just got a client that has extreme switches so I also need to familiarize myself with the switches) The ports seem to be off. I get no response even l2 from the switch. I assume I need an initial configuration which means i need a console cable . What is the minimum config that I need to do to get the switch to power the cameras and allow them to receive dhcp addresses from a router?

RE: initial setup x250e

Ram3 — Wed, 02 Aug 2017 10:22:00 GMT

Please see the below provided Knowledge base articles for your reference:

https://gtacknowledge.extremenetworks.com/articles/How_To/Create-VLAN-in-EXOS

https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-enable-disable-inline-power-PoE-in-EXOS

https://gtacknowledge.extremenetworks.com/articles/Solution/IP-Camera-not-getting-enough-power-to-function

https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-configure-the-DHCP-server-on-a-VLAN-in-EXOS

RE: initial setup x250e

Ariyakudi_Srini — Wed, 02 Aug 2017 10:24:00 GMT

Hi Benzion Nussbaum,

The below articles give you the initial vlan configuration in the switch and also configure IP address to them.

https://gtacknowledge.extremenetworks.com/articles/How_To/Create-VLAN-in-EXOS

https://gtacknowledge.extremenetworks.com/articles/How_To/Configure-IP-address-on-a-VLAN

The output of "show ports " should give you the idea from the flags if the ports are Disabled "D" or Enabled "E".

If the ports are disabled, you can enable the ports with the command "enable ports ".d

Also check the status of the POE ports with the command "show inline-power port " to see if they are disabled or enabled or what the port state is in regards to POE capability.

Regards,
Muthuraman

RE: initial setup x250e

Karthik_Mohando — Wed, 02 Aug 2017 10:24:00 GMT

Hi Benzion,

Here is an article which have information on how to console in to EXOS switches.

https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-console-into-Extreme-and-Enterasys-...

All the ports will be part of vlan Default (untagged) means any end devices can be connected to ports and it will work (which does not send tagged frames)

In order to power up a POE device additional settings is not needed in most of the cases unless Advanced Power Management is required, if that is the case please refer to this article on how to enable this via LLDP
https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-configure-LLDP-for-Extreme-switches...

One more and very specific to IP cameras
https://gtacknowledge.extremenetworks.com/articles/Solution/IP-Camera-not-getting-enough-power-to-fu...

RE: initial setup x250e

Benzion_Nussbau — Wed, 02 Aug 2017 10:33:00 GMT

The switches i received are default yet when i plug a computer into any port . i get no lights. When i plug into the management port i get lights but without a set IP i cant access anything. I guess I need a console cable. Shouldnt the switch work at least at the l2 level straight out of the box?

RE: initial setup x250e

Ariyakudi_Srini — Wed, 02 Aug 2017 10:36:00 GMT

Hi Benzion Nussbaum,

It ideally should for the default vlan. All the ports in factory default state are assigned to the default vlan.

Please console into the switch and check the state of the ports using the command "show ports ".

Regards,
Muthuraman