topic Hello. Please Help!! X460G2 is running with formware version 22.1.1.5. in ExtremeSwitching (EXOS/Switch Engine)

Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Angel_Pavon1 — Tue, 07 Mar 2017 02:41:00 GMT

My X460G2 was rebooted and upgraded to firmare version 22.1.1.5. This was intermittent about six hours. Then I rebooted again and its up. But can u help me?... What does this los´ mean?

03/06/2017 02:10:22.37 Slot-1: EPM Started
03/06/2017 02:10:22.36 Slot-1: Booting after System Failure.
03/06/2017 02:10:22.26 Slot-2: Booting after System Failure.
03/06/2017 02:10:22.18 Slot-3: Booting after System Failure.
03/06/2017 02:10:21.25 Slot-1: Changing to watchdog warm reset mode

thanks.!!

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Patrick_Voss — Tue, 07 Mar 2017 02:44:00 GMT

Hello Angel,

Did you pull the plug on the switches?

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Angel_Pavon1 — Tue, 07 Mar 2017 05:39:00 GMT

Hi Patrick no I didn´t, just ther rebooted by itselve.

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Tripathy__Priya — Tue, 07 Mar 2017 10:54:00 GMT

To me this is something found to be the switch lost power and this is either a power cable problem or the power supplying the switch went out throwing these log message later:

Slot-1: Booting after System Failure.

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Patrick_Voss — Tue, 07 Mar 2017 20:52:00 GMT

The fact that all 3 switches rebooted at the same time makes me believe that the power source needs to be looked into.

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Angel_Pavon1 — Wed, 08 Mar 2017 06:02:00 GMT

I found the problem, and yes affectively it was the power. Thanks a lot. One more cuestion.
What do you think about firmware version 22.1.1.5?
Do you know if this has some problems whith another versions?

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Drew_C — Wed, 08 Mar 2017 06:02:00 GMT

Angel, that release is very new and has not received any patches yet. There are a few issues with SSH that I believed are resolved in 22.2, but it also is quite new. That shouldn't be a deterrent, but rather something to consider. Check the release notes for each to review known issues.

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Tooley__Akiko — Wed, 08 Mar 2017 06:02:00 GMT

Please refer to the Release Notes below for 22.1 -
This EXOS version doesn't have the fix for the SSH issues: http://documentation.extremenetworks.com/release_notes/ExtremeXOS/22.1/downloads/ExtremeXOS_22.1_Rel...

Please refer to the Release Notes below for 22.2 -
This EXOS version contains the fix for the SSH issues: http://documentation.extremenetworks.com/release_notes/ExtremeXOS/22.2/downloads/ExtremeXOS_22.2_Rel...

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Angel_Pavon1 — Wed, 08 Mar 2017 06:02:00 GMT

Thanks a lot!!!! Friends.

RE: Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.

Sylvain_Perron — Wed, 08 Mar 2017 06:02:00 GMT

Hi Angel,

I have the same problem, so what was your conclusion about the error. Did you change the power supply? power cord?

Thanks
Sylvain