https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58559#M17343 When the ports are in 40 Gig mode you will only have port 49,53,57 and 61 available for use. If you partition the ports to 4x10 Gig you will have the NP (Not Present) ports also available.<BR /> <BR /> conf port 49 partition 4x10G<BR /> conf port 53 partition 4x10G<BR /> conf port 57 partition 4x10G<BR /> conf port 61 partition 4x10G<BR /> Thu, 01 Dec 2016 16:11:00 GMT OscarK 2016-12-01T16:11:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58558#M17342 Switch: X670-G2<BR /> FW: 21.1.14<BR /> <BR /> Hi guys,<BR /> <BR /> I would like to add some ports (49 to 56) to the switch using two OSPF 4x10G Modules. When inserted the two modules I see the following:<BR /> <BR /> Port Summary Monitor Thu Dec 1 09:07:50 2016Port Display VLAN Name Port Link Speed Duplex<BR /> # String (or # VLANs) State State Actual Actual<BR /> =======================================================================<BR /> 48 OK20 E A 10G FULL<BR /> 49 OK20 E R<BR /> 50 OK20 E NP<BR /> 51 OK20 E NP<BR /> 52 OK20 E NP<BR /> 53 OK20 E R<BR /> 54 OK20 E NP<BR /> 55 OK20 E NP<BR /> 56 OK20 E NP<BR /> <BR /> How do I manage to get all ports ready?<BR /> <BR /> Greetings Jory<BR /> <BR /> Thu, 01 Dec 2016 15:57:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58558#M17342 Jory_Kienstra 2016-12-01T15:57:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58559#M17343 When the ports are in 40 Gig mode you will only have port 49,53,57 and 61 available for use. If you partition the ports to 4x10 Gig you will have the NP (Not Present) ports also available.<BR /> <BR /> conf port 49 partition 4x10G<BR /> conf port 53 partition 4x10G<BR /> conf port 57 partition 4x10G<BR /> conf port 61 partition 4x10G<BR /> Thu, 01 Dec 2016 16:11:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58559#M17343 OscarK 2016-12-01T16:11:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58560#M17344 Thanks for the quick responds Oscar Thu, 01 Dec 2016 16:15:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58560#M17344 Jory_Kienstra 2016-12-01T16:15:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58561#M17345 The command to partition the ports is as below,<BR /> <BR /> configure ports [port_list | all] partition [4x10G | 1x40G | 1x100G | 10x10G ]<BR /> <BR /> After you make a configuration change, you must do one of the following to apply the change:<BR /> For X670-G2 and X770 switches you can reboot the switch.<BR /> Thu, 01 Dec 2016 16:17:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/how-to-activate-ports-49-64-on-x670-g2/m-p/58561#M17345 Ariyakudi_Srini 2016-12-01T16:17:00Z