https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23203#M2215 Hi Drew,<BR /> <BR /> Could you please explain more about upgrade the links to 10G via XGM module for X450a?<BR /> <BR /> current model is 24-port 1000BASE-X SFP plus 4-port 10/100/1000BASE-T. <BR /> Anyway can we upgrade to 10G uplink?<BR /> <BR /> BRdgs,<BR /> Paul Tue, 02 Dec 2014 22:49:00 GMT Paul11 2014-12-02T22:49:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23177#M2189 After i enable Lacp .. port is not sharing. Utilization is high on Link 1 only. <BR /> I want to use <B>load balance on both links</B>. <BR /> Please kindly see the below output and advice thanks.<BR /> <BR /> <I><B>* I try L2 static, L3_L4 and LACP. all the same ports are not load balance. *</B></I><BR /> <BR /> <I>enable sharing 1 grouping 1,4</I><BR /> <BR /> <I>enable sharing 1 grouping 1,4 L3_L4</I><BR /> <BR /> <I><U>enable sharing 1 grouping 1,4 algorithm address-based L3_L4 lacp<BR /> </U></I><BR /> <BR /> CoreSW # sh port 1,4 utilization bandwithPort Link Link Rx Peak Rx Tx Peak Tx<BR /> State Speed % bandwidth % bandwidth % bandwidth % bandwidth<BR /> ================================================================================<BR /> Link_1&gt; A 1000 <B>82.06 </B> 94.94 <B> 48.23 </B> 55.72<BR /> Link_2&gt; A 1000 <B>0.25 </B> 0.30 <B>1.34</B> 1.57<BR /> ================================================================================<BR /> &gt; indicates Port Display Name truncated past 8 characters<BR /> Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback<BR /> <BR /> CoreSW #sh sharing <BR /> Load Sharing Monitor<BR /> Config Current Agg Ld Share Ld Share Agg Link Link Up<BR /> Master Master Control Algorithm Group Mbr State Transitions<BR /> ==============================================================================<BR /> 1 1 LACP L3_L4 1 Y A 0<BR /> L3_L4 4 Y A 0<BR /> ==============================================================================<BR /> Link State: A-Active, D-Disabled, R-Ready, NP-Port not present, L-Loopback<BR /> Load Sharing Algorithm: (L2) Layer 2 address based<BR /> (L3_L4) Layer 3 address and Layer 4 port based<BR /> Number of <B>load sharing trunks</B>:<B> 1<BR /> </B><BR /> <BR /> Core2 # <B><I>sh lacp lag 1</I></B><BR /> Lag Actor Actor Partner Partner Partner Agg Actor <BR /> Sys-Pri Key MAC Sys-Pri Key Count MAC <BR /> --------------------------------------------------------------------------------<BR /> 1 0 0x03e9 00:04:96:34:b2:e1 0 0x03e9 2 00:04:96:34:b2:e0<BR /> <BR /> Port list:<BR /> <BR /> Member Port Rx Sel Mux Actor Partner <BR /> Port Priority State Logic State Flags Port <BR /> --------------------------------------------------------------------------------<BR /> 1 0 <B>Current </B> Selected Collect-Dist A-GSCD-- 1001 <BR /> 4 0 Current Selected Collect-Dist <B> A-GSCD--</B> 1012 <BR /> ================================================================================<BR /> Actor Flags: A-Activity, T-Timeout, G-Aggregation, S-Synchronization<BR /> C-Collecting, D-Distributing, F-Defaulted, E-Expired<BR /> Tue, 02 Dec 2014 08:57:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23177#M2189 Paul11 2014-12-02T08:57:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23178#M2190 What model do you use in this example ? (Summit X250, 460, BD ? )<BR /> <BR /> LACP is between two extreme switches or server and 1 extreme switch ? (other vendor ?)<BR /> <BR /> What EXOS is on the switch ?<BR /> <BR /> --<BR /> Jarek<BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23178#M2190 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23179#M2191 Thanks <A href="https://community.extremenetworks.com/#" target="_blank" rel="nofollow noreferrer noopener">Jarek</A>,<BR /> <BR /> Core1 and Core 2 using <B>X450a-24x<BR /> </B><BR /> LACP is between two Core Switches.<BR /> ExtremeXOS version<B> 15.3.1.4 <BR /> <BR /> Please advice thanks.<BR /> <BR /> </B>We want to use <B>load balance on both links</B>. <B><BR /> </B> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23179#M2191 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23180#M2192 I have two X250e with config like bellow:<BR /> "enable sharing 24 grouping 21-24 algorithm address-based L3_L4"<BR /> <BR /> and all is working well (EXOS ver 15.3.1.4-1-30).<BR /> <BR /> <U></U>Did you enabled sharing on both swicthes?<BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23180#M2192 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23181#M2193 could you please share the outcome of <BR /> <BR /> sh port 21,24 utilization bandwith Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23181#M2193 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23182#M2194 Yes i did sharing on both switches. Thanks.<BR /> <BR /> Please kindly share the show command of<BR /> <BR /> show port 21-24 utilization bandwidth<BR /> <BR /> <B>Is it load balance on port 21-24 links?</B> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23182#M2194 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23183#M2195 Paul,<BR /> <BR /> you set those commands on switch like bellow:<BR /> enable sharing 1 grouping 1,4<BR /> enable sharing 1 grouping 1,4 L3_L4<BR /> enable sharing 1 grouping 1,4 algorithm address-based L3_L4 lacp<BR /> <BR /> or only :<BR /> <BR /> enable sharing 1 grouping 1,4 algorithm address-based L3_L4 lacp<BR /> <BR /> I have on my switches:<BR /> <BR /> enable sharing 24 grouping 21-24 algorithm address-based L3_L4 lacp<BR /> <BR /> # sh ports 21-24 utilization bandwidth <BR /> Port Link Link Rx Peak Rx Tx Peak Tx<BR /> State Speed % bandwidth % bandwidth % bandwidth % bandwidth<BR /> ================================================================================<BR /> 21 A 100 0.00 0.01 0.02 8.27<BR /> 22 A 100 1.61 1.61 45.28 45.28<BR /> 23 A 100 0.02 0.02 0.00 7.97<BR /> 24 A 100 1.54 2.96 43.32 90.63<BR /> ================================================================================<BR /> <BR /> --<BR /> Jarek<BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23183#M2195 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23184#M2196 I use only one command same like you. But the both links are not load share as i mentioned above. Anyway how can i load balance on these port. Please advice Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23184#M2196 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23185#M2197 Link1 is 82 % and Link2 is only 0.25 % We want to achive load balanced on link1 and link2 Really appreciate your help and advice Jarek. Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23185#M2197 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23186#M2198 What exactly exos do you have 15.3.1.4-p1-xx &lt;-?<BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23186#M2198 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23187#M2199 Sorry my current active version is 15.3.3.5. 15.3.1.4 is on other partition. Thanks. Is it bug or firmware not supported? I do need your adivce on this. The links are in live production network. Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23187#M2199 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23188#M2200 Hmm, I don't use 15.3.3.5. Maybe there is a bug...<BR /> Can you show me from both switches:<BR /> sh sharing<BR /> sh lacp<BR /> sh lacp counters <BR /> sh lacp lag 1 detail <BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23188#M2200 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23189#M2201 I will provide it later. Currently i m outside. Thanks alot. Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23189#M2201 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23190#M2202 Core2 # sh sharing <BR /> Load Sharing Monitor<BR /> Config Current Agg Ld Share Ld Share Agg Link Link Up<BR /> Master Master Control Algorithm Group Mbr State Transitions<BR /> ==============================================================================<BR /> 1 1 LACP L3_L4 1 Y A 0<BR /> L3_L4 4 Y A 0<BR /> ==============================================================================<BR /> Link State: A-Active, D-Disabled, R-Ready, NP-Port not present, L-Loopback<BR /> Load Sharing Algorithm: (L2) Layer 2 address based<BR /> (L3_L4) Layer 3 address and Layer 4 port based<BR /> Number of load sharing trunks: 1<BR /> <BR /> ************************************************************************************<BR /> ************************************************************************************<BR /> <BR /> Core2 # sh lacp <BR /> <BR /> LACP Up : Yes<BR /> LACP Enabled : Yes<BR /> System MAC : 00:04:96:34:b2:e0<BR /> LACP PDUs dropped on non-LACP ports : 19 <BR /> <BR /> Lag Actor Actor Partner Partner Partner Agg <BR /> Sys-Pri Key MAC Sys-Pri Key Count <BR /> --------------------------------------------------------------------------------<BR /> 1 0 0x03e9 00:04:96:34:b2:e1 0 0x03e9 2<BR /> ================================================================================<BR /> <BR /> Core2 # sh lacp lag 1<BR /> <BR /> Lag Actor Actor Partner Partner Partner Agg Actor <BR /> Sys-Pri Key MAC Sys-Pri Key Count MAC <BR /> --------------------------------------------------------------------------------<BR /> 1 0 0x03e9 00:04:96:34:b2:e1 0 0x03e9 2 00:04:96:34:b2:e0<BR /> <BR /> Port list:<BR /> <BR /> Member Port Rx Sel Mux Actor Partner <BR /> Port Priority State Logic State Flags Port <BR /> --------------------------------------------------------------------------------<BR /> 1 0 Current Selected Collect-Dist A-GSCD-- 1001 <BR /> 4 0 Current Selected Collect-Dist A-GSCD-- 1012 <BR /> ================================================================================<BR /> Actor Flags: A-Activity, T-Timeout, G-Aggregation, S-Synchronization<BR /> C-Collecting, D-Distributing, F-Defaulted, E-Expired<BR /> <BR /> ************************************************************************************<BR /> ************************************************************************************<BR /> <BR /> Core2 # sh lacp lag 1 detail <BR /> <BR /> Lag Actor Actor Partner Partner Partner Agg Actor <BR /> Sys-Pri Key MAC Sys-Pri Key Count MAC <BR /> --------------------------------------------------------------------------------<BR /> 1 0 0x03e9 00:04:96:34:b2:e1 0 0x03e9 2 00:04:96:34:b2:e0<BR /> <BR /> Up : Yes<BR /> Enabled : Yes<BR /> Unack count : 0<BR /> Wait-for-count : 0<BR /> Current timeout : Long<BR /> Activity mode : Active<BR /> Defaulted Action : Delete<BR /> Receive state : Enabled<BR /> Transmit state : Enabled<BR /> Selected count : 2<BR /> Standby count : 0<BR /> LAG Id flag : Yes<BR /> S.pri:0 , S.id:00:04:96:34:b2:e0, K:0x03e9<BR /> T.pri:0 , T.id:00:04:96:34:b2:e1, L:0x03e9<BR /> <BR /> Port list:<BR /> <BR /> Member Port Rx Sel Mux Actor Partner <BR /> Port Priority State Logic State Flags Port <BR /> --------------------------------------------------------------------------------<BR /> 1 0 Current Selected Collect-Dist A-GSCD-- 1001 <BR /> 4 0 Current Selected Collect-Dist A-GSCD-- 1012 <BR /> ================================================================================<BR /> Actor Flags: A-Activity, T-Timeout, G-Aggregation, S-Synchronization<BR /> C-Collecting, D-Distributing, F-Defaulted, E-Expired<BR /> <BR /> ************************************************************************************<BR /> ************************************************************************************<BR /> Core1# show ports sharing <BR /> Load Sharing Monitor<BR /> Config Current Agg Ld Share Ld Share Agg Link Link Up<BR /> Master Master Control Algorithm Group Mbr State Transitions<BR /> ==============================================================================<BR /> 1 1 LACP L3_L4 1 Y A 0<BR /> L3_L4 12 Y A 0<BR /> ==============================================================================<BR /> Link State: A-Active, D-Disabled, R-Ready, NP-Port not present, L-Loopback<BR /> Load Sharing Algorithm: (L2) Layer 2 address based<BR /> (L3_L4) Layer 3 address and Layer 4 port based<BR /> Number of load sharing trunks: 1<BR /> <BR /> currently i don't have the log for Core1, I will provide for the Core1 also. Thanks.<BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23190#M2202 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23191#M2203 Paul you have on core2 ports 1,4 in lacp and on core1 ports 1 and 12? Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23191#M2203 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23192#M2204 Hi jarek, Yes correct. It make any different please. Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23192#M2204 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23193#M2205 From show sharing I see that Link Up Transitions in both switches are 0.<BR /> Can you show from both:<BR /> sh lacp counters<BR /> sh configuration | inc shari<BR /> <BR /> I asked about ports, because I had understood that you set on both switches:<BR /> enable sharing 1 grouping 1,4 algorithm address-based L3_L4 lacp<BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23193#M2205 Jarek 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23194#M2206 Thanks Jarek,<BR /> <BR /> Core 1<BR /> enable sharing 1 grouping 1, 12 algorithm address-based L3_L4 lacp<BR /> <BR /> Core 2<BR /> sh configuration | inc shari<BR /> enable sharing 1 grouping 1, 4 algorithm address-based L3_L4 lacp<BR /> <BR /> will provide the command output tomorrow. thank.<BR /> <BR /> Tue, 02 Dec 2014 14:01:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23194#M2206 Paul11 2014-12-02T14:01:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23195#M2207 Try these steps:<BR /> If<BR /> 1.configure sharing address-based custom<BR /> <BR /> check if it load shares<BR /> <BR /> else<BR /> configure sharing address-based custom hash-algorithm [xor | crc-16 | crc-32]<BR /> try CRC-16----If it doesnt help try CRC-32<BR /> <BR /> One or the other way changing hashing must help. Tue, 02 Dec 2014 19:16:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23195#M2207 PARTHIBAN_CHINN 2014-12-02T19:16:00Z https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23196#M2208 Hi <A href="https://community.extremenetworks.com/#" target="_blank" rel="nofollow noreferrer noopener">PARTHIBAN</A>,<BR /> <BR /> I will try tomorrow morning. Thanks a lot for the information. Thanks. Tue, 02 Dec 2014 19:16:00 GMT https://community.extremenetworks.com/t5/extremeswitching-exos-switch/port-load-sharing/m-p/23196#M2208 Paul11 2014-12-02T19:16:00Z