topic VLAN Interfaces Graph in ExtremeSwitching (EXOS/Switch Engine)

VLAN Interfaces Graph

Mrxlazuardin — Sun, 07 Dec 2014 23:13:00 GMT

Hi,

I'm trying to graph the VLAN interfaces traffic on BlackDiamond by using SNMP based RRD tools like Zenoss, Cacti, etc. The tools can show the VLAN interfaces including the tag and name of each one but the traffic is always zero. Is there any way to have such graphs?

Best regards,

RE: VLAN Interfaces Graph

Ravisekar__Raja — Mon, 08 Dec 2014 00:01:00 GMT

Hello Lazuardi Nasution,

What is the OID , you are using ??. We have Extreme MIB for each EXOS which can be downloaded from the portal. Starting in EXOS 12.5 there is support for VLAN statistics and for that there is a separate private SNMP table (extremePortVlanStatsTable)

As soon you have enabled VLAN statistics on a VLAN /port combination you can collect that using the following OID table:

iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).extreme(1916).extremeAgent(1).extremeVlan(2).extremeVlanStatsGroup(8).extremePortVlanStatsTable(2)

You can use below command for vlan statistics

configure ports [port_list|all] monitor vlan vlan_name {rx-only | tx-only}

But another point to be noted is , vlan statistics will occupy your ACL slice so configuring too many ports can lead to in-sufficient resources . While implementing have a check on your ACL slice resources.

Regards

Rajamanickam R

RE: VLAN Interfaces Graph

Seymur_Aliyev — Fri, 25 Dec 2015 15:34:00 GMT

Hello Rajamanickam

We had 2 switch ,one of them is Extreme switch (12.4.1.7).Second of them is black diamond(12.5)

So I have 2 question about that.
1)is it possible active vlan statistica in 12.4?
2)I could not understand "But another point to be noted is , vlan statistics will occupy your ACL slice so configuring too many ports can lead to in-sufficient resources . While implementing have a check on your ACL slice resources"...could you give detail information
If i active all vlan statistica (12.5) ,can it create problem in switch? for example Some cpu or or resource?or maybe some process ?

Thanks

RE: VLAN Interfaces Graph

Zdeněk_Pala — Sat, 26 Dec 2015 16:17:00 GMT

There are some hardware resources what are on the chip and are used for ACLs. These resources are limited (everything is limited)... What Raja noted is that if you want to use both: heavy ACLs and heavy monitoring then you can run out of these resources...

You can check manuals and search for "slice" to understand the architecture.

RE: VLAN Interfaces Graph

Seymur_Aliyev — Thu, 31 Dec 2015 14:18:00 GMT

Ok,We have not access list in switch,but we have 170 vlans in Blackdiamond.We want to monitoring vlans from cacti.My question is that.How can i check to resource which i monitor to all vlans?
Second question is that,what is rrecommendation that how many vlan I can monitor?
Thanks

RE: VLAN Interfaces Graph

Seymur_Aliyev — Thu, 07 Jan 2016 12:15:00 GMT

Hi,I have activated configure ports [port_list|all] monitor vlan vlan_name {rx-only | tx-only},But i don't see in Cacti,What is the problem

Port Vlan Rx Frames Rx Byte Tx Frame Tx Byte Count Count Count Count
================================================================================
BSC21_Nw GboverIP_BSC21 - 248795532 - -

RE: VLAN Interfaces Graph

Seymur_Aliyev — Thu, 07 Jan 2016 13:55:00 GMT

Cacti
IF-MIB::ifHCInOctets.1000076 = Counter64: 0

iF-MIBI::ifHCOutOctets.1000076 = Counter64: 0

.1.3.6.1.2.1.31.1.1.1.10.1000076 = Counter64: 0

.1.3.6.1.2.1.31.1.1.1.10.1000076 = Counter64: 0

Blackdiamond

sh snmp get 1.3.6.1.2.1.2.2.1.10.1000076

mib_2.2.2.1.10.1000076 = 0

CACTI
IF-MIB::ifIndex.1000076 = INTEGER: 1000076IF-MIB::ifDescr.1000076 = STRING: VLAN vlan number ("vlan")
IF-MIB::ifType.1000076 = INTEGER: propVirtual(53)
IF-MIB::ifMtu.1000076 = INTEGER: 1500
IF-MIB::ifSpeed.1000076 = Gauge32: 0
IF-MIB::ifPhysAddress.1000076 = STRING:
IF-MIB::ifAdminStatus.1000076 = INTEGER: up(1)
IF-MIB::ifOperStatus.1000076 = INTEGER: up(1)
IF-MIB::ifLastChange.1000076 = Timeticks: (9900) 0:01:39.00
IF-MIB::ifInOctets.1000076 = Counter32: 0
IF-MIB::ifInUcastPkts.1000076 = Counter32: 0
IF-MIB::ifInNUcastPkts.1000076 = Counter32: 0
IF-MIB::ifInDiscards.1000076 = Counter32: 0
IF-MIB::ifInErrors.1000076 = Counter32: 0
IF-MIB::ifInUnknownProtos.1000076 = Counter32: 0
IF-MIB::ifOutOctets.1000076 = Counter32: 0
IF-MIB::ifOutUcastPkts.1000076 = Counter32: 0
IF-MIB::ifOutNUcastPkts.1000076 = Counter32: 0
IF-MIB::ifOutDiscards.1000076 = Counter32: 0
IF-MIB::ifOutErrors.1000076 = Counter32: 0
IF-MIB::ifOutQLen.1000076 = Gauge32: 0
IF-MIB::ifSpecific.1000076 = OID: SNMPv2-SMI::internet
SNMPv2-SMI::mib-2.16.22.1.1.1.1.2.1.3.6.1.2.1.2.2.1.1.1000076 = Hex-STRING: 08
SNMPv2-SMI::mib-2.16.22.1.1.1.1.3.1.3.6.1.2.1.2.2.1.1.1000076 = Hex-STRING: C9 00
SNMPv2-SMI::mib-2.16.22.1.1.1.1.4.1.3.6.1.2.1.2.2.1.1.1000076 = INTEGER: 1000076
IF-MIB::ifName.1000076 = STRING: GboverIP_BSC21
IF-MIB::ifInMulticastPkts.1000076 = Counter32: 0
IF-MIB::ifInBroadcastPkts.1000076 = Counter32: 0
IF-MIB::ifOutMulticastPkts.1000076 = Counter32: 0
IF-MIB::ifOutBroadcastPkts.1000076 = Counter32: 0
IF-MIB::ifHCInOctets.1000076 = Counter64: 0
IF-MIB::ifHCInUcastPkts.1000076 = Counter64: 0
IF-MIB::ifHCInMulticastPkts.1000076 = Counter64: 0
IF-MIB::ifHCInBroadcastPkts.1000076 = Counter64: 0
IF-MIB::ifHCOutOctets.1000076 = Counter64: 0
IF-MIB::ifHCOutUcastPkts.1000076 = Counter64: 0
IF-MIB::ifHCOutMulticastPkts.1000076 = Counter64: 0
IF-MIB::ifHCOutBroadcastPkts.1000076 = Counter64: 0
IF-MIB::ifLinkUpDownTrapEnable.1000076 = INTEGER: disabled(2)
IF-MIB::ifHighSpeed.1000076 = Gauge32: 0
IF-MIB::ifPromiscuousMode.1000076 = INTEGER: false(2)
IF-MIB::ifConnectorPresent.1000076 = INTEGER: false(2)
IF-MIB::ifAlias.1000076 = STRING:
IF-MIB::ifCounterDiscontinuityTime.1000076 = Timeticks: (0) 0:00:00.00
IF-MIB::ifTestId.1000076 = INTEGER: 0
IF-MIB::ifTestStatus.1000076 = INTEGER: notInUse(1)
IF-MIB::ifTestType.1000076 = OID: SNMPv2-SMI::internet
IF-MIB::ifTestResult.1000076 = INTEGER: none(1)
IF-MIB::ifTestCode.1000076 = OID: SNMPv2-SMI::internet
IF-MIB::ifTestOwner.1000076 = STRING:
SNMPv2-SMI::mib-2.85.1.1.1.2.1000076 = Gauge32: 125
SNMPv2-SMI::mib-2.85.1.1.1.3.1000076 = INTEGER: 1
SNMPv2-SMI::mib-2.85.1.1.1.4.1000076 = Gauge32: 2
SNMPv2-SMI::mib-2.85.1.1.1.5.1000076 = IpAddress: 0.0.0.0
SNMPv2-SMI::mib-2.85.1.1.1.6.1000076 = Gauge32: 100
SNMPv2-SMI::mib-2.85.1.1.1.7.1000076 = Timeticks: (0) 0:00:00.00
SNMPv2-SMI::mib-2.85.1.1.1.8.1000076 = Timeticks: (0) 0:00:00.00
SNMPv2-SMI::mib-2.85.1.1.1.9.1000076 = Timeticks: (0) 0:00:00.00
SNMPv2-SMI::mib-2.85.1.1.1.10.1000076 = Counter32: 0
SNMPv2-SMI::mib-2.85.1.1.1.11.1000076 = Counter32: 1
SNMPv2-SMI::mib-2.85.1.1.1.12.1000076 = INTEGER: 0
SNMPv2-SMI::mib-2.85.1.1.1.13.1000076 = Gauge32: 0
SNMPv2-SMI::mib-2.85.1.1.1.14.1000076 = Gauge32: 2
SNMPv2-SMI::mib-2.85.1.1.1.15.1000076 = Gauge32: 10

RE: VLAN Interfaces Graph

Seymur_Aliyev — Wed, 24 Feb 2016 12:35:00 GMT

Hello Dears
We have done upgrade 15.6 to Blackdiamonds,we have also done monitor vlan,but we can't see statistica in Blackdiamonds.What is the problem?

Thanks

RE: VLAN Interfaces Graph

welisson — Wed, 20 Sep 2017 23:57:00 GMT

Hi bro,

Were you able to get this information?
Tks