topic RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization? in ExtremeSwitching (EXOS/Switch Engine)

Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

Rien_Maurik — Fri, 16 Oct 2015 14:03:00 GMT

Hello.

I want to know in a Black Diamond 8810 the Utilization of the Layer 3 traffic between the Vlan's.

For the Physical interfaces the command to see the utilization is "show ports utilization". Is there also a command to see the same for the Vlan interfaces or the layer 3 process?

RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

BrandonC — Sun, 18 Oct 2015 22:23:00 GMT

Hi Rien,

There is the command 'show ipstats'. Does this look like what you are looking for?

* master.5 # show ipstats IP Global Statistics InReceives = 7 InUnicast = 0 InBcast = 0 InMcast = 7 InHdrErr = 0 Bad vers = 0 Bad chksum = 0 Short pkt = 0 Short hdr = 0 Bad hdrlen = 0 Bad length = 0 InDelivers = 7 InDiscards = 0 Bad Proto = 0 OutRequest = 7 OutDiscard = 0 OutNoRoute = 0 Forwards = 0 ForwardOK = 0 Fwd Err = 0 NoFwding = 0 Redirects = 0 No route = 0 Bad TTL = 0 Bad MC TTL = 0 Bad IPdest = 0 Blackhole = 0 Output err = 0 MartianSrc = 0 FragCreate = 0 FragOKs = 0 FragFails = 0 Global ICMP Statistics OutResp = 0 OutError = 0 InBadcode = 0 InTooshort = 0 Bad chksum = 0 In Badlen = 0 echo reply In = 0 Out = 0 destination unreachable In = 0 Out = 0 - protocol unreachable In = 0 Out = 0 redirect In = 0 Out = 0 echo In = 0 Out = 0 router advertisement In = 0 Out = 0 time exceeded In = 0 Out = 0 Global IGMP Statistics Out Query = 0 Out Report = 0 Out Leave = 0 In Query = 0 In Report = 0 In Leave = 0 In Error = 0 Router Interface Default inet 1.1.1.1 netmask 255.0.0.0 broadcast 1.255.255.255 Stats: IN OUT 5 5 packets 160 160 octets 5 5 Mcast pkts 0 0 Bcast pkts 0 0 errors 0 0 discards 0 unknown protos Router Interface p_eaps inet 2.2.2.2 netmask 255.0.0.0 broadcast 2.255.255.255 Stats: IN OUT 4 4 packets 128 128 octets 4 4 Mcast pkts 0 0 Bcast pkts 0 0 errors 0 0 discards 0 unknown protos

-Brandon

RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

Rien_Maurik — Mon, 19 Oct 2015 12:23:00 GMT

Hello Brandon

Thank you for your abswer, but the results of the "show ipstats" command is not the information i 'm looking for.

I'm looking for the utilization of the routing ( layer3 ) between the vlan's in packets per second, or byte per second or Bite per second.

The Command "show port utilisation" show the packets transfert per second, I want to see the same for the packets between the vlan's.

The problem with the "show IP stats" is that the output shows only the total of packet, not the packet per second or the Peak packet per second

- Rien

RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

BrandonC — Mon, 19 Oct 2015 12:23:00 GMT

Hi Rien,

Unfortunately, EXOS does not provide a command to show this information.

If you like, I can open up a feature request for this in your name.

-Brandon

RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

Rien_Maurik — Mon, 19 Oct 2015 12:23:00 GMT

Hello Brandon

Thank You for your time and offer, but in the mean time we also open a gtac case with this question. The Gtac engineer (Kawawa Chitiya) advice us to us a policy to measure the packets leaving the vlan.

This sollution ísn't great but is working good enough fur us.

thank you for your help

greeting Rien

RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

Stephen_Elliot1 — Mon, 19 Oct 2015 12:23:00 GMT

Hi there - I've been watching this query as I have the same requirement.
Brandon, perhaps you could open a feature request after all.
In our case we have multiple vlans on an ISP link and we'd like to be able to determine how much traffic each vlan is sending/receiving.

RE: Black Diamond 8810; what is the command to show the layer 3 (inter vlan) switching utilization?

Stephane_Grosj1 — Mon, 19 Oct 2015 12:23:00 GMT

Hi,

this last requirement is a bit different. If you only need statistics Tx/Rx per vlan, you can do it already.

config port monitor vlan
sh vlan statistics

example:
Slot-1 Stack.5 # configure port all monitor vlan "switches"
Slot-1 Stack.6 # sh vlan "switches" statistics
VLAN Statistics Wed Nov 4 11:30:36 2015
Vlan Rx Total Rx Byte Tx Total Tx Byte
Frames Count Frames Count
================================================================================
switches 133 11088 0 0

================================================================================
0->Clear Counters U->page up D->page down ESC->exit