topic RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance. in ExtremeSwitching (EXOS/Switch Engine)

hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jun_Papa — Sat, 19 Aug 2017 15:11:00 GMT

hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

davidj_cogliane — Sat, 19 Aug 2017 17:07:00 GMT

Unless you are trying to use stp for redundancy I would recommend elrp. ELRP is very easy to configure and reliable. The only downside is that it lacks the dynamic enable when the loop condition is cleared. Best of luck,

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Nick_Yakimenko — Sat, 19 Aug 2017 17:07:00 GMT

A very big disadvantage of using ELRP is that it blocks whole port instead of blocking specific vlan in which the loop was occured

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jun_Papa — Sat, 19 Aug 2017 17:07:00 GMT

Thank you Nick for the reply, the situation is like this, the iptv contractor requires this command in every tv port.

cisco command;
interface FastEthernet0/10
switchport protected
no ip address
spanning-tree portfast

i am looking for the same commande in extreme.

Thanks,

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jeremy_Gibbs — Sat, 19 Aug 2017 18:28:00 GMT

I think this does it configure stpd "s0" ports link-type edge 1:2

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jun_Papa — Sat, 19 Aug 2017 18:39:00 GMT

i got this line;
502.2 # configure stpd "s0" ports link-type edge 6,7
Error: Port 6 is not a member of STP domain s0
Error: Port 7 is not a member of STP domain s0
Error: Command aborted due to input errors, no changes made

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jeremy_Gibbs — Sat, 19 Aug 2017 19:37:00 GMT

What version of code are you running? If you type show stpd ?... what stp domains are listed?

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jun_Papa — Sun, 20 Aug 2017 15:55:00 GMT

version 16.23
MSTP Global Configuration:
MSTP Region Name : 000496984141
MSTP Format Identifier : 0
MSTP Revision Level : 3
MSTP Digest : ac:36:17:7f:50:28:3c:d4:b8:38:21:d8:ab:26:de:62
Common and Internal Spanning Tree (CIST) : ----
Total Number of MST Instances (MSTI) : 0

Name Tag Flags Ports Bridge ID Designated Root Rt Port Rt Cost
s0 0000 D----- 1 8000000496984141 0000000000000000 ------- 0

Total number of STPDs: 1 STP Flush Method: VLAN and Port
STP Filter Method: System-wide

Flags: (C) Topology Change, (D) Disable, (E) Enable, (R) Rapid Root Failover
(T) Topology Change Detected, (M) MSTP CIST, (I) MSTP MSTI

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jeremy_Gibbs — Sun, 20 Aug 2017 23:07:00 GMT

Here is my config

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jeremy_Gibbs — Sun, 20 Aug 2017 23:07:00 GMT

enable stpd s0 auto-bind vlan Admin
enable stpd s0 auto-bind vlan AdminComputer
enable stpd s0 auto-bind vlan CiscoVideo
....
configure stpd s0 ports link-type edge 1:20
configure stpd s0 ports edge-safeguard enable 1:20
configure stpd s0 ports bpdu-restrict enable 1:20

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jun_Papa — Mon, 21 Aug 2017 10:32:00 GMT

thanks you... i got this
Stpd: s0 Stp: ENABLED Number of Ports: 4
Rapid Root Failover: Disabled
Operational Mode: 802.1D Default Binding Mode: 802.1D
802.1Q Tag: (none)
Ports: 11*,13,14,23
Participating Vlans: Default,iptv
Auto-bind Vlans: Default,iptv
Bridge Priority : 32768
Operational Bridge Priority: 32768
BridgeID : 80:00:00:04:96:98:41:41
Designated root : 80:00:00:04:96:98:41:41
RootPathCost: 0 Root Port : ----
MaxAge : 20s HelloTime : 2s ForwardDelay : 15s
CfgBrMaxAge : 20s CfgBrHelloTime: 2s CfgBrForwardDelay: 15s
Topology Change Time : 35s Hold time : 1s
Topology Change Detected : TRUE Topology Change : TRUE
Number of Topology Changes : 1
Time Since Last Topology Change: 19s
Topology Change initiated locally on Port 23
Topology Change last received on Port none from none
Backup Root : Off Backup Root Activated : FALSE
Loop Protect Event Window : 180s Loop Protect Threshold : 3
New Root Trap : On Topology Change Trap : Off
Tx Hold Count : 6
Participating VLANs:
VLAN Tag Number of Ports
Ports
-------------------------------------------------------------------------------
Default 1 1
23(F)
iptv 14 4
11*(D),13(F),14(D),23(F)
Flags: B-Blocking, D-Disabled, F-Forwarding, I-Listening, L-Learning

RE: hi guys what is the equivalent cisco command; spanning-tree and portfast to extreme.. Thanks in advance.

Jeremy_Gibbs — Mon, 21 Aug 2017 10:32:00 GMT

Is it now working as expected? Did you set auto-bind up for the VLAN's? IDK if EZ-spantree is default on 16.xxx switches, but it is now for 22.xx.xx code. You can install this as an XMOD to help your config.
https://github.com/extremenetworks/EXOS_Apps/tree/master/EZ_SpanningTree