topic RE: make Vlan 800 Series in ExtremeSwitching (Other)

make Vlan 800 Series

LOSI_STEFANO — Wed, 17 Feb 2016 23:57:00 GMT

Can someone help me configure VLANs in a switch 800 series ??I created a VLAN 'phone' in addition to the VLAN 'default' but I can not figure out how to make them communicate.

RE: make Vlan 800 Series

Zdeněk_Pala — Thu, 18 Feb 2016 00:03:00 GMT

Hi I believe this should help you: http://youtu.be/SFn-9fdEOv0 Search on youtube for 800 vlan configuration Regards Zdenek

RE: make Vlan 800 Series

LOSI_STEFANO — Thu, 18 Feb 2016 00:07:00 GMT

ok, I configured the vlan but how can I do to communicate the two vlan ??

RE: make Vlan 800 Series

Ronald_Dvorak — Thu, 18 Feb 2016 00:07:00 GMT

Make sure to configure the GVRP port settings or it will not work....

https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-Assign-a-Port-To-a-Vlan-on-the-800-...

RE: make Vlan 800 Series

Zdeněk_Pala — Thu, 18 Feb 2016 00:11:00 GMT

If you need to communicate between VLANs, you need routing and configure default gateway on the endsystems to use the ip address of the vlan interface. Routing is supported on 800series. I do not have screenshots with me 

RE: make Vlan 800 Series

LOSI_STEFANO — Thu, 18 Feb 2016 00:16:00 GMT

I'm sorry... what you mean by 'endsystems' ?? Thank you

RE: make Vlan 800 Series

LOSI_STEFANO — Thu, 18 Feb 2016 00:19:00 GMT

Can you tell me the steps to enable VLAN to communicate ??

RE: make Vlan 800 Series

Ronald_Dvorak — Thu, 18 Feb 2016 00:19:00 GMT

I don't think that the 800series could route - AFAIK you'd only configure one IP for mgmt of the switch but not different VLAN interfaces.

https://gtacknowledge.extremenetworks.com/articles/Q_A/Does-the-800-Series-support-Layer-3-switching

RE: make Vlan 800 Series

Zdeněk_Pala — Thu, 18 Feb 2016 00:19:00 GMT

Based on datasheet it does support routing. It does have Routing section... It is quite confusing.

RE: make Vlan 800 Series

LOSI_STEFANO — Thu, 18 Feb 2016 14:54:00 GMT

I have 2 VLAN (dafault, phone).'Default' has the interface ip 192.168.253.22 gateway with firewall (192.168.253.1)
'Phone' has Cooma interface ip 192.168.250.1

I created a static route 192.168.253.1 with 192.168.250.0/24 gateway but not working

RE: make Vlan 800 Series

Mike_D — Sat, 20 Feb 2016 01:27:00 GMT

Hello Losi,

The 800 - as already established - supports static routing.

Forwarding should be enabled by default.

I think we can help you out - but the configuration info given is confusing.

Can you label a simple diagram with addresses, gateway etc?

Stick figure simple. xx-----XX-----x or something similar? We should be able to clear up some of the muddle.

This

static route 192.168.253.1 with 192.168.250.0/24 gateway

seems wrong. but much depends on what was intended.

If you can describe what you would like to have happen for routing (vs the route statement above) I'm sure the community can help.

By the way, is the route being entered into the 800 series?

Regards,

Mike