AP2605 factory reset

Pawel_Maczka — Tue, 02 Sep 2014 19:16:00 GMT

I forgot a password to my access point AP2605, I'v tried to push reset buton for few seconds but with no effect, What is the correct procedure fo factory reset ?

RE: AP2605 factory reset

Jason1 — Tue, 02 Sep 2014 19:48:00 GMT

Hello Pawel,

I have been able to factory reset this by pushing the reset button for about 10 seconds. If you have telnet or console access to the 2605, you can use "set factory" to reset to defaults.

Thanks,
Jason

RE: AP2605 factory reset

Pawel_Maczka — Tue, 02 Sep 2014 20:03:00 GMT

When I connect through console or telnet, AP keeps asking me for a login and password. When I press the reset button AP restarts and shows:

set_log_level:L40:set LOG_LEVEL to LOG_INFO.
ruMgmtGetBackupTunnel: No backup tunnel found
apCfgOpModeSet:L5097:SET REBOOT:unit:0,opMode:0
apCfgRadioChannelSet - Wlan0 - 5300 MHz is not part of country code US, or not p
ossible with this hardware
apCfgRadioChannelSet - Wlan1 - set value: 2437, AutoChanSelect: 1, channel: 2437
Key Table (Static) now [16]
Key Table (Static) now [16]
apCfgHostNameSetDefault: AP2605-0500010103050267
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlan0
by removing B/G mode
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlan1
by removing A mode
apCfgGatewayAddrUpdate - enabling ReAuthenticateFlag
wlanDisconnectClients: cat VNS_CAT_ALL
ALARM : 98 sec in cycle 11: AccessPoint Rebooting: Reset and Restore to DEFAU
LTS
L|00:01:38.866|806bcf50|ru_discov.c:426|ru_discov_check_timeout|# delta_s 90
wlan0 Disable interrupts 1024
Reset the HW
status = 0
wlan1 Disable interrupts 8192
Reset the HW
status = 0
Rebooting AP...
Waiting for cfg file to finish writing...done. Checksum: f6b4
apNolWrite - No Radar Info for wlan0, not initialized
apNolWrite - No Radar Info for wlan1, not initialized

ar531x rev 0x00005742 firmware startup...
SDRAM TEST...PASSED
Before Init AE531x DMA Engine

Atheros AR5312 default version 3.0.0.43A
Chantry Networks BootROM Software Version: 2.2.0

0
auto-booting...

Attaching to TFFS... done.
Loading /fl/bp200.img...1790960
Starting at 0x804c46e0...

/fl/ - Volume is OK
ru_image_signature_read: Image signature not set.
confDataExtract():"confData.bin" AP2605 length 1652 07.41.01.0192 is up to date

wlanChannSetConfData: /fl/confData.bin Ver 30 len 1652
wlanChannSetConfData: 6.1 conformance set data p 0x80ede4c0
set_log_level:L40:set LOG_LEVEL to LOG_INFO.
ruMgmtGetBackupTunnel: No backup tunnel found
apCfgCountryCodeSet:L4788:SET REBOOT:countrycode:840
apCfgRadioChannelSet - Wlan0 - set value: 5300, AutoChanSelect: 0, channel: 5300
apCfgRadioChannelSet - Wlan1 - set value: 2437, AutoChanSelect: 0, channel: 2437
apCfgDhcpcModeSet - enabling ReAuthenticateFlag
Key Table (Static) now [16]
Key Table (Static) now [16]
apCfgHostNameSetDefault: AP2605-0500010103050267
Pre-parsing Configuration File "/fl/apcfg".
Configuration file checksum: f6b4 is good
Reading Configuration File "/fl/apcfg".
apCfgRadioChannelSet - Wlan0 - set value: 5180, AutoChanSelect: 0, channel: 5180
Cfg AP2605-0500010103050267, New AP2605-0500010103050267, size 25
Configuration file checksum: f6b4 is good
ru_readSharedConfig: Shared config sensor signature invalid, 0x33333333
L|00:00:02.183|80fbfdf0|usrEndLib.c:96|usrEndLibInit|# Add interfaces B
wds notify eth: Can not send data through message queue, errno = d0003
L|00:00:04.149|80fbfdf0|datasocket.c:180|aeDataPathAttach|# Attaching tunnel pro
tocol to ae0
clusters: 1152 free: 896 usage: 256
print_log_level:L50:Current LOG_LEVEL is LOG_INFO.
L|00:00:04.149|80fbfdf0|m2Task.c:170|m2WdgInit|# Initialize timer
L|00:00:04.149|80fbfdf0|m2Task.c:139|m2Dot1xCBInit|# Initialize
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlan0
by removing B/G mode
ar5212AttachRateTables - attching rate tables
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlanne
tEvent: Starting tNetEvent...
0 by removing B/G mode
wlanInitChannelList: wlanInitChannelList -- 8 channels
apInit - Created Rate Set for radio: 0
Rate Set for Radio-0 OpBss-0: 6000(b) 9000 12000(b) 18000 24000(b) 36000 48000 5
4000
apVlanReset - Initializing all Vns's for wlan: 0
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlan1
by removing A mode
ar5212AttachRateTables - attching rate tables
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlan0
by removing B/G mode
ar5212FillCapabilityInfo - WARNING - Restricting HW mode capabilities for wlan1
by removing A mode
wlanInitChannelList: wlanInitChannelList -- 11 channels
apInit - Created Rate Set for radio: 1
Rate Set for Radio-1 OpBss-0: 1000(b) 2000(b) 5500(b) 11000(b) 6000 9000
apVlanReset - Initializing all Vns's for wlan: 1
Attaching interface lo0...done

Adding 11959 symbols for standalone.
ru_image_personality_check: AP startup role -1

AP SNMP Agent Initialization Started!!!

LLDP TASK STARTED==============================

AP SNMP Agent Initialization Done!!!
SUPP1X: EAP INFO Initialized EAP
SUPP1X: EAP INFO Created EAP Instance
SUPP1X: EAP INFO Initialized EAP1X
SUPP1X: MSS MAJOR supp1x new state disconnected/failure
SUPP1X: MSS MAJOR supp1x new state init
L|00:00:05.283|80fbfdf0|m2Task.c:199|m2AddDot1xCallBack|# Adding CB
apCservInit - Initializing Connection Services
dot1xTask - Dot1x task started
dot1xTask - radio: 0, resetting vlans: TLV_DICT out of date, updating...
0 1 2 3 4 5 6 7
dot1xTask - radio: 1, resetting vlans: 0 1 2 3 4 5 6 7
Serial No.: '0500010103050267'
Software version: '07.41.01.0192.M.00'
L|00:00:05.583|806dea00|wassp_common.c:67|open_wasspsock|# Open socket for wassp
_port=13910
bpVlanStateCheck - FAILD - No VNS-es enabled
bpVlanStateCheck - FAILD - No VNS-es enabled
L|00:00:06.283|80fbfdf0|siapp.c:284|siappInit_leg|# Our MAC addr is 00:1f:45:7e:
14:8d
Ready
Cserv Task Started
ru_mgmt start waiting for dot1x authentication to proceed
L|00:00:06.816|80732f40|ru_led.c:370|ru_led_handler|# No change, mode -214410780
8
ru_mgmt finish waiting for dot1x authentication to proceed
ru_discov started pid 1 pthread_self -2140418224
ru_discov: reRegister 0, state 0x80fbfe90
Cannot open /dev/urandom, using rand()
DHCP sync semaphore created, dhcpc_semId 0x80fbe0c0
L|00:00:08.816|806bcf50|ru_discov.c:426|ru_discov_check_timeout|# delta_s 0
STEP<0> (1/5) @ 0:00.000: Setup AP ethernet interface,
do dhcp static 0
The Host Name for DHCP Discovery is: AP2605-0500010103050267
Awaiting dhcpBind ... 30,29,28, Done.
IPaddr: 10.5.5.22
apCfgIpAddrSet - enabling ReAuthenticateFlag
IP address changed. Removing file acinfo.conf.
apCfgIpMaskSet - enabling ReAuthenticateFlag
DNS 1: 10.8.8.9
DNS 2: 10.8.8.3
Domain: 'arpwaw.local'.
apCfgGatewayAddrUpdate - enabling ReAuthenticateFlag
Gateway: 10.1.1.1
STEP<1> (1/1) @ 0:04.050: Read saved AC info conf file,
L|00:00:12.866|806bcf50|cmn_siapp.c:122|cmn_siapp_joinmc|# Joined MCast group 22
4.0.1.178
STEP<3> (1/1) @ 0:04.050: Check for static AC IP addresses,
STEP<4> (1/1) @ 0:04.050: Start discovery threads,
SLP thread started
DNS thread started
ru_discov_main_slp: threadId 0x806b7f10, pid 1
SLPU: Finding AC managers for service='siemens'
dhcp_discov_option: start DHCP INFORM option 0
Awaiting dhcpcInformGet... ru_discov_main_dns: threadId 0x806b55e0, pid 1
dhcp_discov_option: start DHCP INFORM option 1
3, Done.
SLPU: Finding RU managers for service='siemens'
dhcp_discov_option: start DHCP INFORM option 0
Awaiting dhcpcInformGet... 3, Done.
ru_discov_vendor_class_decode: total_length: 5, Type:-36, Data Length:3
DNS 1: 10.8.8.9
DNS 2: 10.8.8.3
Domain: 'arpwaw.local'.
Configured hostname is blank. Using default of 'Controller'.
Using DHCP provided DomainSuffix of 'arpwaw.local'.
Requesting "Controller.arpwaw.local" from 10.8.8.9
Awaiting dhcpcInformGet... Requesting "Controller.arpwaw.local" from 10.8.8.3
3, Done.
SLPM: Finding AC managers for service='siemens'
Add node 0x80fbc9f0, IP 192.168.168.2
ru_start_discov_threads: thread_SLP 1, thread_DNS 1
STEP<5> (1/1) @ 0:05.050: Connect to AC_RU_manager,
Attempting connection 1 to AC_manager 192.168.168.2
SLPM: Finding RU managers for service='siemens'
L|00:00:18.866|806bcf50|ru_discov.c:426|ru_discov_check_timeout|# delta_s 10
Attempting connection 2 to AC_manager 192.168.168.2

AP2605 login:

RE: AP2605 factory reset

Pawel_Maczka — Tue, 02 Sep 2014 20:04:00 GMT

It still tryin to connect to "AC_manager 192.168.168.2", witch we do not have anymore.

RE: AP2605 factory reset

Ronald_Dvorak — Tue, 02 Sep 2014 21:06:00 GMT

RE: AP2605 factory reset

Pawel_Maczka — Wed, 03 Sep 2014 12:34:00 GMT

Big thanks e~=2.718 works !

topic RE: AP2605 factory reset in ExtremeWireless (General)

AP2605 factory reset

RE: AP2605 factory reset

RE: AP2605 factory reset

RE: AP2605 factory reset

RE: AP2605 factory reset

RE: AP2605 factory reset