Not working the value for transmit power in smart-rf-policy

i_khlebnikov — Mon, 15 Feb 2021 17:50:26 GMT

Hello

I have a NX5500 controller and some AP7532.

Firmware version - 5.9.8.1-004R

I configured smart-rf-policy with limit Tx Power values

smart-rf-policy new_sm
group-by area
group-by floor
assignable-power 5GHz max 14
assignable-power 5GHz min 10
assignable-power 2.4GHz max 16
assignable-power 2.4GHz min 10
channel-list 5GHz 36,40,44,48,132,136,140
channel-width 5GHz 20MHz
no select-shutdown

I use this smart-rf-policy in a rf-domain and some APs

rf-domain ShBD
geo-coordinates 62.5129680 40.1983120
timezone Etc/GMT+3
country-code ru
use smart-rf-policy new_sm
use nsight-policy Monitoring
layout area ShBD
layout area ShBD floor Floor1 map-location flash:/floorplans/ShBD-1Floor.jpg units meters
tree-node city Office campus ShBD
control-vlan 1

ap7532 48-9B-D5-A5-3A-11
use profile Office_AP_Inside
use rf-domain ShBD
hostname AP082
layout-coordinates 260.9 -626.7
area ShBD
floor Floor1

When I try to check TXPower values by command show wireless radio on rf-domain, there are default value for Tx power in output

WLC-TS-1-1#show wireless radio on ShBD
----------------------------------------------------------------------------------------------
RADIO                RADIO-MAC             RF-MODE        STATE       CHANNEL    POWER #CLIENT
----------------------------------------------------------------------------------------------
AP082:R1             48-9B-D5-CF-23-B0 2.4GHz-wlan           On     6 ( smt) 20 (smt)       1
AP082:R2             48-9B-D5-CF-95-10   5GHz-wlan           On   132 ( smt) 20 (smt)       1
AP081:R1             48-9B-D5-CE-F0-20 2.4GHz-wlan           On     1 ( smt) 20 (smt)       0
AP081:R2             48-9B-D5-CF-8C-60   5GHz-wlan           On    36 ( smt) 14 (smt)       0
AP080:R1             48-9B-D5-CF-1D-20 2.4GHz-wlan           On    11 ( smt) 20 (smt)       6
AP080:R2             48-9B-D5-CF-95-70   5GHz-wlan           On    44 ( smt) 14 (smt)       3
----------------------------------------------------------------------------------------------

Why the configured values for Tx Power are not applied?

Best regards,

Khlebnikov Ilya

Re: Not working the value for transmit power in smart-rf-policy

Christoph_S — Mon, 15 Feb 2021 21:35:13 GMT

Hello Khlebnikov,

Looking at the smart-rf config, you should not be using both of these settings together:

group-by area
group-by floor

Depending on your deployment, either use group-by area or group-by floor.

Here’s an article on same: https://extremeportal.force.com/ExtrArticleDetail?an=000079173

Moreover, please look into upgrading the firmware to the latest 5.9.8 version.

Thank you

Re: Not working the value for transmit power in smart-rf-policy

i_khlebnikov — Sun, 21 Feb 2021 23:56:43 GMT

Hello Christoph,

I deleted “ group-by area ” command. Now all APs have correct TX power’s values.

Thank you for helping!

Best regards,

Khlebnikov Ilya

topic Not working the value for transmit power in smart-rf-policy in ExtremeWireless (WiNG)

Not working the value for transmit power in smart-rf-policy

Re: Not working the value for transmit power in smart-rf-policy

Re: Not working the value for transmit power in smart-rf-policy