topic Re: Mint neighbours are not showing correctly in ExtremeWireless (WiNG)

Mint neighbours are not showing correctly

Warlock26 — Tue, 28 Jul 2020 18:43:20 GMT

one of my site having around 22 AP and all this device are online and able to view in rf-domain but when i checked the mint neighbours it not showing neighboring AP list as a part of troubleshooting i have pinged from from ap to ap its working fine also i checked the adoption status it shows ap is adopted to controller correctly .and when i checked wireless clients ,device are showing in ap but not in controller and we are only using single vlan but still mint neighbour establishment is not happening.

Re: Mint neighbours are not showing correctly

ckelly — Tue, 28 Jul 2020 20:01:21 GMT

How did you check for MINT neighbors? (What commands?)

Did you run the commands on an AP or on the controller?

Re: Mint neighbours are not showing correctly

Warlock26 — Wed, 29 Jul 2020 00:32:26 GMT

i tried # show mint neighbours in Access Point but it didn't show the neighbouring AP list.

Re: Mint neighbours are not showing correctly

ckelly — Wed, 29 Jul 2020 01:04:58 GMT

Can you run these and post the outputs?

show mint info

show mint mlcp

show mint stats

I’m assuming these APs are being managed by a WiNG controller…

Is the WiNG controller the RF-Domain Manager or this RF-Domain...or one of the APs?

check by running show global domain managers and look for the RFDomain and then check the Host Name column to see if it’s an AP or a controller

Re: Mint neighbours are not showing correctly

Warlock26 — Wed, 29 Jul 2020 12:59:26 GMT

below are the output i am getting

#show mint info
Mint ID: 55.B4.B4.40
0 Level-1 neighbors
Level-1 LSP DB size 1 LSPs (1 KB)
1 Level-2 neighbors
Level-2 LSP DB size 2 LSPs (1 KB)
Level-2 gateway is self
Level-2 leaf node
Reachable adopters: 12.BC.6D.0A
Max level-1 path cost: 0 (to 55.B4.B4.40)

#show mint mlcp
MLCP VLAN state: MLCP_DISCOVERING
MLCP VLAN Hello Interval: 4s(default), Adjacency hold time: 13s(default)
Potential VLAN links:
All VLANs were scanned 1022 times
MLCP IP: ENABLED
MLCP IPv6: ENABLED
MLCP IP/IPv6 state: MLCP_DONE
MLCP IP Hello Interval: 15s(default), Adjacency hold time: 46s(default)
Potential L3 Links:
172.17.100.144, 172.19.97.144
Link created to 172.19.97.144:24576 level 2

#show mint stats
0 Level-1 neighbors
Level-1 LSP DB size 1 LSPs (1 KB)
Last Level-1 SPFs took 0.000s
Level-1 SPF (re)calculated 5 times.
1 Level-1 paths.
1 Level-2 neighbors
Level-2 LSP DB size 2 LSPs (1 KB)
Last Level-2 SPFs took 0.000s
Level-2 SPF (re)calculated 24 times.

and when i tried # show global domain manager in Access point i got AP in hostname column

Re: Mint neighbours are not showing correctly

Warlock26 — Wed, 29 Jul 2020 13:17:09 GMT

issue has been resolved actually i didn't enabled vlan for control traffic in rf-domain once i enable that its start to work and i am able to view mint neighbours in ap now and also i am able to view wireless clients from controller side

Re: Mint neighbours are not showing correctly

ckelly — Wed, 29 Jul 2020 21:06:44 GMT

There you go.

Noticed that MINT level-1 was not seeing any of your neighbor APs...which relies on the defined control VLAN. That was going to be my next question. 🙂

Good catch.