AP7532 Wing 5.9.8.0 does not meet throughput requirement

Arthurooo — Fri, 20 Dec 2024 13:31:11 GMT

Hello,

I am currently running an AP7532 with wing software 5.9.8.0 and I am able to see that we don't meet the throughput requirement for 802.11 ac.

On my configuration, I am running the following settings on radio 2:

- Data rates custom basic- mcs-1s mcs-2s mcs-3s

- Data rates mcs qam only

- Channel 44ww

By doing iperf3 testing, we are able to see that download/upload over TCP and UDP don't go higher than 220~240 Mbps, whereas the wireless client statistics show that phy rates is 1.3 Gbps.

The configuration is the following:

******************************************

Configuration of AP7532 version 5.9.8.0-002R
!
!
version 2.7
!
!
client-identity-group default
load default-fingerprints
!
ip access-list BROADCAST-MULTICAST-CONTROL
permit tcp any any rule-precedence 10 rule-description "permit all TCP traffic"
permit udp any eq 67 any eq dhcpc rule-precedence 11 rule-description "permit DHCP replies"
deny udp any range 137 138 any range 137 138 rule-precedence 20 rule-description "deny windows netbios"
deny ip any 224.0.0.0/4 rule-precedence 21 rule-description "deny IP multicast"
deny ip any host 255.255.255.255 rule-precedence 22 rule-description "deny IP local broadcast"
permit ip any any rule-precedence 100 rule-description "permit all IP traffic"
!
mac access-list PERMIT-ARP-AND-IPv4
permit any any type ip rule-precedence 10 rule-description "permit all IPv4 traffic"
permit any any type arp rule-precedence 20 rule-description "permit all ARP traffic"
!
ip snmp-access-list default
permit any
!
firewall-policy default
no ip dos tcp-sequence-past-window
no firewall enable
no stateful-packet-inspection-l2
!
!
mint-policy global-default
!
meshpoint-qos-policy default
!
wlan-qos-policy default
no wmm power-save
qos trust dscp
qos trust wmm
accelerated-multicast 239.1.172.203 classification video
accelerated-multicast 239.1.172.204 classification video
accelerated-multicast 239.1.172.205 classification video
accelerated-multicast 239.1.172.206 classification video
accelerated-multicast 239.1.172.207 classification video
!
radio-qos-policy default
admission-control video max-clients 25
admission-control video max-roamed-clients 25
admission-control video max-airtime-percent 150
admission-control video reserved-for-roam-percent 12
accelerated-multicast max-client-streams 4
accelerated-multicast stream-threshold 100
accelerated-multicast client-timeout 120
!
wlan 1
ssid SSID1
vlan 5
bridging-mode local
encryption-type ccmp
authentication-type none
no fast-bss-transition over-ds
wpa-wpa2 psk 0 123456789
data-rates 5GHz custom basic-mcs-1s mcs-2s mcs-3s
client-load-balancing
wireless-client count-per-radio 200
!
wlan 2
ssid SSID2
vlan 1
bridging-mode local
encryption-type ccmp
authentication-type none
no broadcast-ssid
no answer-broadcast-probes
no fast-bss-transition over-ds
wpa-wpa2 psk 0 123456789
wireless-client count-per-radio 200
!
wlan 3
ssid SSID3
vlan 11
bridging-mode local
encryption-type ccmp
authentication-type none
no broadcast-ssid
no answer-broadcast-probes
no fast-bss-transition over-ds
wpa-wpa2 psk 0 123456789
wireless-client count-per-radio 200
!
wlan CONFIG_ID
ssid 9f4609d5773e9d9cd1684f4e539fa417
vlan 1
bridging-mode local
encryption-type ccmp
authentication-type none
no fast-bss-transition over-ds
wpa-wpa2 psk 0 12345EDCBAX
!
smart-rf-policy default
no select-shutdown
!
!
management-policy default
no telnet
no http server
https server
no rest-server
ssh
user admin password 1 d04a0379c5cb1558583793a3c43f83afdb17d2fd562f9f8a78ed02b1857207d0 role superuser access all
snmp-server manager v2
snmp-server community 0 private rw
snmp-server community 0 public ro
snmp-server user snmptrap v3 encrypted des auth md5 0 admin123
snmp-server user snmpmanager v3 encrypted des auth md5 0 admin123
!
event-system-policy default
!
profile ap7532 default
use enterprise-ui
no ip igmp snooping
no ip igmp snooping forward-unknown-multicast
no ipv6 mld snooping forward-unknown-multicast
autoinstall configuration
autoinstall firmware
load-balancing balance-band-loads
crypto ikev1 policy ikev1-default
isakmp-proposal default encryption aes-256 group 2 hash sha
crypto ikev2 policy ikev2-default
isakmp-proposal default encryption aes-256 group 2 hash sha
crypto ipsec transform-set default esp-aes-256 esp-sha-hmac
crypto ikev1 remote-vpn
crypto ikev2 remote-vpn
crypto auto-ipsec-secure
crypto load-management
crypto remote-vpn-client
interface radio1
channel 1w
power 20
data-rates gn
beacon dtim-period 1
wlan 1 bss 1 primary
wlan 2 bss 2 primary
wlan 3 bss 3 primary
no dynamic-chain-selection
no probe-response retry
mu-mimo
transmit-beamforming
interface radio2
channel 44ww
power 20
data-rates custom basic-mcs-1s mcs-2s mcs-3s
beacon dtim-period 1
wlan 1 bss 1 primary
wlan 2 bss 2 primary
wlan 3 bss 3 primary
no dynamic-chain-selection
data-rates mcs qam-only
interface ge1
switchport mode trunk
switchport trunk allowed vlan 1,5,11
no cdp receive
no cdp transmit
no lldp receive
no lldp transmit
interface vlan1
ip address dhcp
ip dhcp client request options all
interface vlan5
interface vlan11
interface pppoe1
use event-system-policy default
use firewall-policy default
use client-identity-group default
logging on
no cdp run
no lldp run
service pm sys-restart
router ospf
adoption-mode controller
!
rf-domain default
timezone Europe/Paris
country-code fr
use smart-rf-policy default
!
ap7532 94-9B-2C-2A-68-78
use profile default
use rf-domain default
hostname ap7532
location default
ip default-gateway 192.168.104.1
interface radio1
no shutdown
channel 1w
interface radio2
no shutdown
channel 44ww
power 20
data-rates custom basic-mcs-1s mcs-2s mcs-3s
beacon dtim-period 1
wlan 1 bss 1 primary
wlan 2 bss 2 primary
wlan 3 bss 3 primary
use radio-qos-policy default
antenna-mode default
no dynamic-chain-selection
mu-mimo
data-rates mcs qam-only
interface vlan1
no description
ip address 192.168.104.3/24
no ip nat
interface vlan5
no description
ip address 10.224.250.3/12
no use dhcp-server-policy
no virtual-controller
rf-domain-manager capable
no ip dns-server-forward
!
!
end

******************************************

Any idea for improvements ?

Thank you for your help.

Regards,
Arthur

Re: AP7532 Wing 5.9.8.0 does not meet throughput requirement

Daren_E — Mon, 23 Dec 2024 14:05:12 GMT

Morning Arthur,

Can you re-run the test without 2.4 enabled.
Also can you ensure the configuration for WLAN/Radio QOS and int rad 2 is configurated as follows.

!
wlan-qos-policy default
qos trust dscp
qos trust wmm
!
radio-qos-policy default
!
interface radio2
channel 44ww
power 20
beacon dtim-period 1
wlan 1 bss 1 primary
wlan 2 bss 2 primary
wlan 3 bss 3 primary
no dynamic-chain-selection
!
Note: also remove custom data rates from the wlan.

If speed is still slow please send output from "show wi cl st rf" and "sh wi ra st rf" for review.

Re: AP7532 Wing 5.9.8.0 does not meet throughput requirement

Arthurooo — Mon, 03 Mar 2025 11:09:59 GMT

Hi Daren,

Thank you for the reply and the help.
I'll be able to test the recommendations you sent + the command lines in the coming month. I'll keep you posted.

Thank you,
Arthur

topic Re: AP7532 Wing 5.9.8.0 does not meet throughput requirement in ExtremeWireless (WiNG)

AP7532 Wing 5.9.8.0 does not meet throughput requirement

Re: AP7532 Wing 5.9.8.0 does not meet throughput requirement

Re: AP7532 Wing 5.9.8.0 does not meet throughput requirement