https://community.extremenetworks.com/t5/faqs/generation-of-a-trap-upon-securestack-power-status-change/m-p/46973#M428 Article ID: 7130 <BR /> <BR /> <B>Products</B><BR /> SecureStack C2<BR /> Firmware 3.02.32 and lower<BR /> SecureStack B2<BR /> Firmware 2.01.10 and lower<BR /> SecureStack A2<BR /> Firmware 1.01.20 and lower<BR /> C2RPS-PSM<BR /> C2RPS-POE <BR /> <BR /> <B>Protocols/Features</B><BR /> Trap <BR /> <BR /> <B>Symptoms</B><BR /> Power redundancy<BR /> No SNMP trap is generated upon power status change <BR /> <BR /> <B>Cause</B><BR /> With older firmware, the stack manager unit will not generate an SNMP trap to notify the administrator when the stack loses or gains back its redundant power supply (<A href="http://bit.ly/IAFEZg" target="_blank" rel="nofollow noreferrer noopener">C2RPS-PSM/C2RPS-POE</A>). <BR /> <BR /> <B>Solution</B><BR /> For the C2, upgrade to firmware 3.03.23 or higher.<BR /> For the B2, upgrade to firmware 3.00.14 or higher.<BR /> For the A2, upgrade to firmware 1.01.46 or higher. <BR /> <BR /> As of C2 f/w 3.01.71:When C2RPS-POE is connected to a SecureStack device and power is<BR /> discontinued or provided on the SecureStack C2, itself, or the backup<BR /> power supply (C2RPS-POE), an enterprise mib trap will be generated<BR /> detailing this event.<BR /> As of C2 f/w 3.03.23, B2 f/w 3.00.14, and A2 f/w 1.01.46:When a SecureStack device suffers from a power system failure, the<BR /> system will now send trap from the etsysPsePowerNotification MIB, which<BR /> can be correctly decoded by NetSight Console.<BR /> As of A2 firmware 2.01.00.0010:The SecureStack A2 now supports notification of redundant power supply<BR /> (RPS) status via traps and Syslog messages.<BR /> Pre-upgrade workaround:<BR /> Implement syslog messaging. As a redundant power supply status changes, the event will be duly logged for management review. <BR /> <BR /> Follow-up note:<BR /> As of C2 f/w 5.02.08.0006 and B2 f/w 4.02.08.0006:Added support for the following OIDs to the CTRON-CHASSIS-MIB ctChas<BR /> object:<BR /> <BR /> * ctChasFNB.0 denotes the presence or absence of the FNB.<BR /> * ctChasAlarmEna.0 allows an audible alarm to be either enabled or<BR /> disabled. Setting this object to disable(1) will prevent an audible<BR /> alarm from being heard and will also stop the sound from a current<BR /> audible alarm. Setting this object to enable(2) will allow an audible<BR /> alarm to be heard and will also enable the sound from a current audible<BR /> alarm, if it has previously been disabled.<BR /> * chassisAlarmState.0 denotes the current condition of the power supply<BR /> fault detection circuit. The object value will read<BR /> chassisNoFaultCondition(1) when the chassis is operating with no power<BR /> faults detected and will read chassisFaultCondition(2) when the chassis<BR /> is in a power fault condition. Tue, 03 Dec 2013 20:48:00 GMT FAQ_User 2013-12-03T20:48:00Z https://community.extremenetworks.com/t5/faqs/generation-of-a-trap-upon-securestack-power-status-change/m-p/46973#M428 Article ID: 7130 <BR /> <BR /> <B>Products</B><BR /> SecureStack C2<BR /> Firmware 3.02.32 and lower<BR /> SecureStack B2<BR /> Firmware 2.01.10 and lower<BR /> SecureStack A2<BR /> Firmware 1.01.20 and lower<BR /> C2RPS-PSM<BR /> C2RPS-POE <BR /> <BR /> <B>Protocols/Features</B><BR /> Trap <BR /> <BR /> <B>Symptoms</B><BR /> Power redundancy<BR /> No SNMP trap is generated upon power status change <BR /> <BR /> <B>Cause</B><BR /> With older firmware, the stack manager unit will not generate an SNMP trap to notify the administrator when the stack loses or gains back its redundant power supply (<A href="http://bit.ly/IAFEZg" target="_blank" rel="nofollow noreferrer noopener">C2RPS-PSM/C2RPS-POE</A>). <BR /> <BR /> <B>Solution</B><BR /> For the C2, upgrade to firmware 3.03.23 or higher.<BR /> For the B2, upgrade to firmware 3.00.14 or higher.<BR /> For the A2, upgrade to firmware 1.01.46 or higher. <BR /> <BR /> As of C2 f/w 3.01.71:When C2RPS-POE is connected to a SecureStack device and power is<BR /> discontinued or provided on the SecureStack C2, itself, or the backup<BR /> power supply (C2RPS-POE), an enterprise mib trap will be generated<BR /> detailing this event.<BR /> As of C2 f/w 3.03.23, B2 f/w 3.00.14, and A2 f/w 1.01.46:When a SecureStack device suffers from a power system failure, the<BR /> system will now send trap from the etsysPsePowerNotification MIB, which<BR /> can be correctly decoded by NetSight Console.<BR /> As of A2 firmware 2.01.00.0010:The SecureStack A2 now supports notification of redundant power supply<BR /> (RPS) status via traps and Syslog messages.<BR /> Pre-upgrade workaround:<BR /> Implement syslog messaging. As a redundant power supply status changes, the event will be duly logged for management review. <BR /> <BR /> Follow-up note:<BR /> As of C2 f/w 5.02.08.0006 and B2 f/w 4.02.08.0006:Added support for the following OIDs to the CTRON-CHASSIS-MIB ctChas<BR /> object:<BR /> <BR /> * ctChasFNB.0 denotes the presence or absence of the FNB.<BR /> * ctChasAlarmEna.0 allows an audible alarm to be either enabled or<BR /> disabled. Setting this object to disable(1) will prevent an audible<BR /> alarm from being heard and will also stop the sound from a current<BR /> audible alarm. Setting this object to enable(2) will allow an audible<BR /> alarm to be heard and will also enable the sound from a current audible<BR /> alarm, if it has previously been disabled.<BR /> * chassisAlarmState.0 denotes the current condition of the power supply<BR /> fault detection circuit. The object value will read<BR /> chassisNoFaultCondition(1) when the chassis is operating with no power<BR /> faults detected and will read chassisFaultCondition(2) when the chassis<BR /> is in a power fault condition. Tue, 03 Dec 2013 20:48:00 GMT https://community.extremenetworks.com/t5/faqs/generation-of-a-trap-upon-securestack-power-status-change/m-p/46973#M428 FAQ_User 2013-12-03T20:48:00Z