topic How to enable Wake-on-LAN with NetLogin in Network Architecture & Design

How to enable Wake-on-LAN with NetLogin

Chacko — Wed, 17 May 2017 13:24:00 GMT

Hi,

we have a request to make WoL possible in our network.
I already found that aritcle: https://extremeportal.force.com/ExtrArticleDetail?an=000082951
but I have a few issues:

The first method doesn't work here. I can see, that "show udp-profile" forwards traffic to my dummy-vlan, but the device doesn't wake up. If I send out the WoL packet, when the computer is on, my wireshark can see the incoming WoL packet. I did all the commands, which are described for that method
The second method is not applicable, because we don't want to edit scripts on the switch, when changing a netlogin-port - that is simply too much
The third method is not applicable, because most of our switches doesn't support OnePolicy

I'm sure that I am not the only one who experience these issues - has anyone a working solution for that scenario?

Best Regards
Chacko

RE: How to enable Wake-on-LAN with NetLogin

davidj_cogliane — Wed, 17 May 2017 15:08:00 GMT

Windows 10 seems to disable will by default. It has to do with a default power setting and can be fixed with a gpo. Not sure if this is part of your issue or not, but thought it was worth mentioning.

RE: How to enable Wake-on-LAN with NetLogin

Chacko — Wed, 17 May 2017 15:08:00 GMT

Hi,

ok, good to know.

But I do the testing with Windows 7.
When I configure the test-port without netlogin, the WoL instantly wakes up the computer.

BR
Chacko

RE: How to enable Wake-on-LAN with NetLogin

AnonymousM — Thu, 18 May 2017 18:19:00 GMT

You should consider IP directed broadcast or enable broadcast flooding into the netlogin VLAN.

RE: How to enable Wake-on-LAN with NetLogin

Chacko — Thu, 18 May 2017 18:19:00 GMT

Hi, where do I exactly need to enable that?
We have a NetLogin-VLAN without an IP address and a few Layer-3 VLANs where the clients are assigned to.
BR
Chacko

RE: How to enable Wake-on-LAN with NetLogin

Chacko — Mon, 29 May 2017 16:22:00 GMT

Ok, problem solved.
You need to enable egress broadcasts to the Netlogin-VLAN.
After that is done, it works like stated in the KB-article

RE: How to enable Wake-on-LAN with NetLogin

Tripathy__Priya — Thu, 01 Jun 2017 11:50:00 GMT

Not sure which KB article you have referred. Anyway here is what i can find the procedure from one of the article mentioned earlier. If not then please refer this for your future reference:

https://extremeportal.force.com/ExtrArticleDetail?an=000082951

Anyway good to hear that after enabling the egress broadcast this started to work as expected.

RE: How to enable Wake-on-LAN with NetLogin

mischoe — Tue, 20 Feb 2018 17:31:00 GMT

This solution seems to work for EXOS with Netlogin (802.1x and/or mac).
But the command "netlogin ports [port_list | all] allow egress-traffic [none | unicast | broadcast | all_cast]"
is no more available, if OnePolicy (Enterasys Policy) are used.

As described in command reference: "Enabling ONEPolicy removes the action of this command. This command is supported only in non-policy mode"

I'm not able to find a solution for following scenario:
- X440-G2 L2-Access Switch (no option for making them routing)
- Extreme NAC with Policy
- EXOS 22.3
- One Policy enabled

Regards
Micha