Header Only - DO NOT REMOVE - Extreme Networks

2016-02-08: New GTAC Knowledge Articles January 31 - February 6, 2016

  • 11 February 2016
  • 0 replies

Here are the new articles that were published January 31 - February 06 2016 in GTAC Knowledge:

Sunday, January 31, 2016:
Kernel Oops Crash

Monday, February 01, 2016:
How to create different switch access rules in NAC for LDAP (Advanced Directory) authentication to get different login credentials
BD8810 MSM Rebooting of kernel ooops and HAL process crash
Is it possible to configure syslogs using OSPF loopback interface IP?
Scanner doesn´t work on 3620 AP
Port mirror fails if policy mirror exists 150 class S-series
getAddrchk_mask_e error seen when configuring ipv6 on the identFi wireless controller
How do I confirm that a particular TCP port is open in EXOS?
Clients on one interface unable to access network
IdentiFi | For Load Groups -> Radio Preference, do WLAN's need to be assigned for band steering to work?

Tuesday, February 02, 2016:
CoS not working as expected on SSA running
How to configure an EAPs ring
S-series order of precedence when applying mirrors
Rogue DHCP server violation seen on the trusted-port when trusted-port is configured before enabling the sharing on the trusted-port
Packet loss after adding a port to a LAG (loadshare)
ELRP configuration shows all ports when only subset of ports are enabled
How do I search release notes for known issues?
How to See the Amount of Bandwidth Traffic on a Port using CLI Output?
S-Series Unable to configure Host.0.1 Error Message host.0.1 does not support this feature
Users Receiving IP's from Other Sites subnet on K-Series
RADIUS accounting packets are sent with a MAC address and not the user name from an 802.1X service.
How to clear an ELS100-24TX(M,G) config to Factory Defaults
How do I configure an LACP LAG between EXOS and IdentiFi AP3825i

Wednesday, February 03, 2016:
How to check if the ARP tables in software, hardware and kernel are properly synced up
Windows 10 End Systems Show Up in NAC With Missing OS Family and OS Type
What is the convergence time in a SummitStack when a unit becomes failed?
EXOS - Delay in executing CLI commands
Why is my ipv6 BGP neigbor state in IDLE
netlogin sending trap although traps are disabled for netlogin
LAG Not Forming in S-Series Despite Receiving LACP PDU's From Partner
Why is ExtremeXOS ssh exit status 255 when no error occurs?
CDR data not included in the controller back up
High Pitched Squeal from Summit Power Supply Fan

Thursday, February 04, 2016:
Distance difference between LX and SX GBIC
Unable to read GBIC EEPROM for port error messages
When would the warning message "PIM is currently busy with other tasks. Please try again later." appear in the switch?
S-Series port mirror Showing Only Ten Percent of Traffic From Port Connected to ESX Server
How To Open NetSight and NAC Related Log Files Using NetSight Console
Can the Preregistration Portal printouts be made a different size for printout?
AP crashes or reboots after upgrade to 09.21.05 and enabling 802.11k
AP crash with "Kernel panic - not syncing: out of cookies" after upgrade to 09.21.06 and enabling 802.11k
S-Series Logging Error about GBIC tNimIntr]Unable to perform read data access to pluggable
No FDB entries learned after adding port to VLAN
How to configure RSTP in EXOS for interoperability with Calix

Friday, February 05, 2016:
How to authorise Windows domain user/computer using 802.1x and LDAP lookups to ensure the user AND computer is in the domain, denying access to users with valid domain credentials on BYOD devices.
NAC Troubleshooting Tips - Debug Methodology for SSH or Telnet Mgmt Access Issues
Bgp ipv6 networks not transmitted to bgp neighbor
Scripts run on port element groups in OneView are not pulling in the port information
NAC 802.1x users are rejected by radius server because of improper configuration in Active Directory
What ports are being used by the NAC to join the domain?
Small amount of multicast traffic lost
7100-Series maximum authenticated user capacity
OneView: Cannot open any of the Purview reports

Saturday, February 06, 2016:

0 replies

Be the first to reply!