cancel
Showing results for 
Search instead for 
Did you mean: 

SSL module for x450a24t in home lab environment

Peter_Millard
New Contributor II
Hi there, i have an x450a24t in a home lab environment, and as such have no warranty or support on this device.I am looking to get HTTPS access setup and I believe i need the ssl module to do this.Does anybody have a copy of this they might be able to let me have or point in the right direction to be able to down load this module it would be much appreciated.Many thanks,Peter
8 REPLIES 8

Peter_Millard
New Contributor II
Here you go:-

Home_X450a-24t.1 # show version images
Card Partition Installation Date Version Name Branch
------------------------------------------------------------------------------
Switch primary Fri Aug 18 07:48:53 UTC 2017 15.3.5.2 summitX-15.3.5.2-patch1-14.xos v1535b2-patch1-14
Switch primary Wed Aug 23 08:02:43 UTC 2017 15.3.5.2 summitX-15.3.5.2-patch1-14-ssh.xmod v1535b2-patch1-14
Switch secondary Fri Mar 23 18:55:42 UTC 2012 12.6.2.10 summitX-12.6.2.10-patch1-2.xos v1262b10-patch1-2
Switch secondary Thu Sep 20 21:18:17 BST 2012 12.6.2.10 summitX-12.6.2.10-patch1-2-ssh.xmod v1262b10-patch1-2

Home_X450a-24t.2 # show switch

SysName: Home_X450a-24t
SysLocation:
SysContact:
System MAC: 00:04:96:51:AB:71
System Type: X450a-24t
SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled
Current Time: Fri Sep 1 21:09:08 2017
Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
Boot Time: Mon Aug 28 05:50:02 2017
Boot Count: 33
Next Reboot: None scheduled
System UpTime: 4 days 15 hours 19 minutes 6 seconds
Current State: OPERATIONAL
Image Selected: primary
Image Booted: primary
Primary ver: 15.3.5.2
patch1-14
Secondary ver: 12.6.2.10
Config Selected: primary.cfg
Config Booted: primary.cfg
primary.cfg Created by ExtremeXOS version 15.3.5.2
179524 bytes saved on Fri Aug 25 20:27:23 2017

Home_X450a-24t.3 # show man
[KHome_X450a-24t.3 # show management
CLI idle timeout : Enabled (20 minutes)
CLI max number of login attempts : 3
CLI max number of sessions : 8
CLI paging : Enabled (this session only)
CLI space-completion : Disabled (this session only)
CLI configuration logging : Disabled
CLI scripting : Disabled (this session only)
CLI scripting error mode : Ignore-Error (this session only)
CLI persistent mode : Persistent (this session only)
CLI prompting : Enabled (this session only)
Telnet access : Enabled (tcp port 23 vr all)
: Access Profile : not set
SSH access : Enabled (Key valid, tcp port 22 vr all)
: Access Profile : not set
Web access : Enabled (tcp port 80)
: Access Profile : not set
Total Read Only Communities : 1
Total Read Write Communities : 1
RMON : Disabled
SNMP access : Disabled
: Access Profile : not set
SNMP Compatibility Options :
GETBULK Reply Too Big Action : Too Big Error
IP Fragmentation : Disallow
SNMP Notifications : Enabled
SNMP Notification Receivers : None
SNMP stats: InPkts 0 OutPkts 0 Errors 0 AuthErrors 0
Gets 0 GetNexts 0 Sets 0 Drops 0
SNMP traps: Sent 0 AuthTraps Enabled
SNMP inform: Sent 0 Retries 0 Failed 0
Home_X450a-24t.4 #

Many thanks

BradP
Contributor III
Hi Peter,

Can you provide the results of a "show version images", "show switch" and "show management"? Please redact any personal information that may be in those outputs. I'm mainly just concerned with the active switch partition, if the xmod is installed, and if its applied to the switch.

Thanks
Brad

Peter_Millard
New Contributor II
Just wondering if anyone might be able to shed some light as to why the above article didn't work?

Peter_Millard
New Contributor II
Hi there, Tried the instructions in the document but it keeps saying ssl module not installed. Have verified that the ssh module is installed and running. Many thanks