cancel
Showing results forĀ 
Search instead forĀ 
Did you mean:Ā 

[X440G2-48p-10G4] High CPU utilization caused by cliMaster process?

[X440G2-48p-10G4] High CPU utilization caused by cliMaster process?

SteveNguyen
Extreme Employee
Hi Team,

At customer site, we have an X440G2 Switch that encountered high CPU utilization caused by cliMaster process (~30% in avg, ~70% at peak), even web https/https are disabled & no abnormal log observed as well.
Could you please let me know what is the best approach?
Thank you in advance.

code:
Switch_A.1 # sho sw
SysName: Switch_A
SysLocation: Lab
SysContact: support@extremenetworks.com, +1 888 257 3000
System MAC: 00:04:96:xx:xx:xx
System Type: X440G2-48p-10G4
SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled
Current Time: Thu Feb 21 08:18:18 2019
Timezone: [Auto DST Disabled] GMT Offset: 420 minutes, name is Hanoi.
Boot Time: Wed Oct 18 20:06:59 2017
Boot Count: 11
Next Reboot: None scheduled
System UpTime: 490 days 12 hours 11 minutes 19 seconds
Current State: OPERATIONAL
Image Selected: primary
Image Booted: primary
Primary ver: 21.1.2.14
patch1-2
Secondary ver: 21.1.2.14
Config Selected: primary.cfg
Config Booted: primary.cfg
primary.cfg Created by ExtremeXOS version 21.1.2.14
391114 bytes saved on Thu Feb 21 08:14:57 2019

Switch_A.2 # top
Mem: 508336K used, 467792K free, 0K shrd, 3024K buff, 211764K cached
CPU: 25.5% usr 10.9% sys 0.0% nic 57.8% idle 0.0% io 4.9% irq 0.6% sirq
Load average: 6.24 6.30 6.23 3/201 3806
PID PPID USER STAT RSS %MEM CPU %CPU COMMAND
2029 1 root S 27908 2.8 0 30.2 ./cliMaster
1821 2 root SW< 0 0.0 0 2.3 [bcmLINK.0]

Switch_A.3 # sho cpu-monitoring
CPU Utilization Statistics - Monitored every 5 seconds
-----------------------------------------------------------------------
Process 5 10 30 1 5 30 1 Max Total
secs secs secs min mins mins hour User/System
util util util util util util util util CPU Usage
(%) (%) (%) (%) (%) (%) (%) (%) (secs)
-----------------------------------------------------------------------
System 6.2 6.3 8.6 6.8 6.4 6.4 6.3 33.2 2443.03 2586584.78
aaa 0.0 0.0 0.0 0.0 0.0 0.0 0.0 3.4 725.62 1144.00
acl 0.2 0.1 0.0 0.1 0.0 0.1 0.1 10.9 10905.85 12997.17
bfd 0.0 0.0 0.0 0.2 0.2 0.1 0.1 2.2 5728.83 5679.43
bgp 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.00 0.00
brm 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.00 0.00
cfgmgr 0.8 0.5 0.5 0.6 0.5 0.5 0.5 4.4 6135.00 2150.89
cli 31.3 32.0 28.7 30.2 29.8 29.8 29.7 70.5 15762.98 3042.60
1 ACCEPTED SOLUTION

EtherMAN
Contributor III
High cpu due to cli process is normal and you should see this anytime you log in and issue commands. It can also be caused if and when you trigger a backup of the active configuration. This is why we do all back ups during off hours. Also remember 99 % of what that switch is doing is being done in hardware so having High CPu usage only effects things the cpu has to process and not switch known network traffic.

You should have a log entry at the same time youo see the high usage showing who or what maybe using the cli

View solution in original post

1 REPLY 1

EtherMAN
Contributor III
High cpu due to cli process is normal and you should see this anytime you log in and issue commands. It can also be caused if and when you trigger a backup of the active configuration. This is why we do all back ups during off hours. Also remember 99 % of what that switch is doing is being done in hardware so having High CPu usage only effects things the cpu has to process and not switch known network traffic.

You should have a log entry at the same time youo see the high usage showing who or what maybe using the cli
GTM-P2G8KFN