Hello, colleagues!
X590 stack was with 22.6.1.4.
Issues began when tryed to upgrade stack directly to 30.7.2.1
"Installing to Slot-2(Backup): .....Error: Failed to install image on Slot-2 - tar: corrupted data"
Normally upgraded to 30.2.2.17, but again issues.
Tryed upgrade to "clean" EXOS 30.7 based on this article - Solution: Upgrade attempt fails on EXOS Summit X440-G2 stack | Extreme Portal
How could we upgrade stack without rebuild it? (disassemble, upgrade, assemble)
Maybe somebody faced with such issues?
Thank you!
X590 stack was with 22.6.1.4.
Issues began when tryed to upgrade stack directly to 30.7.2.1
"Installing to Slot-2(Backup): .....Error: Failed to install image on Slot-2 - tar: corrupted data"
Normally upgraded to 30.2.2.17, but again issues.
Tryed upgrade to "clean" EXOS 30.7 based on this article - Solution: Upgrade attempt fails on EXOS Summit X440-G2 stack | Extreme Portal
| Force | |||||||
|
|||||||
but no success.
Tryed to upgrade to 30.3.1.6 but still issues:
Slot-1 X590.4 # install image onie-30.3.1.6.xos
This image will be used only after rebooting the switch!
Installing to primary partition!
Installing to Slot-2(Backup): .....Error: Failed to install image on Slot-2 - tar: corrupted data
Install image failed: (see above error message)
And below messages in logs:
1/23/2021 12:40:04.02 <Noti:EPM.install_status> User XXX: Image installation finished with status failure -tar: can't open '/scratch/onie-30.3.1.6.xos': No such file or directory
11/23/2021 12:40:03.99 <Erro:EPM.Upgrade.Fail> Upgrade failed, script: get new installer failed
11/23/2021 12:40:03.97 <Noti:EPM.Upgrade.Strt> User bigroma: Image upgrade has started.
11/23/2021 12:39:48.22 <Erro:EPM.Upgrade.Fail> Upgrade failed, script: get new installer failed
11/23/2021 12:39:42.64 <Warn:EPM.Upgrade.State> Upgrade status Sent install request to EPM peer(s).
11/23/2021 12:39:42.31 <Warn:EPM.Upgrade.State> Upgrade status Send change partition request to EPM peer(s)
11/23/2021 12:36:31.47 <Info:AAA.LogSsh> Msg from Backup : ERROR: Failed to get file "onie-30.3.1.6.xos" from primary.
11/23/2021 12:36:31.47 <Info:AAA.LogSsh> Msg from Backup : Failed to get file onie-30.3.1.6.xos on backup.
11/23/2021 12:36:30.93 <Erro:tftpd.err> received error packet: 768: write error
11/23/2021 12:35:30.97 <Info:AAA.LogSsh> Msg from Master : Did not send file "onie-30.3.1.6.xos" info to any standby's
11/23/2021 12:35:30.97 <Info:AAA.LogSsh> Msg from Master : Sent file "onie-30.3.1.6.xos" info to backup
Now we have this situation:
->show version images
Card Partition Installation Date Version Name Branch
------------------------------------------------------------------------------
Slot-1 primary Tue Nov 23 12:46:17 EET 2021 30.3.1.6 onie-30.3.1.6.xos builds/xos_30.3/30.3.1.6
Slot-1 secondary Mon Nov 22 21:59:57 EET 2021 30.2.2.17 onie-30.2.2.17.xos 30.2.2.17
Slot-2 primary Tue Nov 23 12:32:35 EET 2021 30.2.2.17 onie-30.2.2.17.xos 30.2.2.17
Slot-2 secondary Mon Nov 22 21:59:07 EET 2021 30.2.2.17 onie-30.2.2.17.xos 30.2.2.17
->show switch
...
Slot: Slot-1 * Slot-2
------------------------ ------------------------
Current State: MASTER BACKUP (In Sync)
Image Selected: secondary secondary
Image Booted: secondary secondary
Primary ver: 30.3.1.6 30.2.2.17
Secondary ver: 30.2.2.17 30.2.2.17
How could we upgrade stack without rebuild it? (disassemble, upgrade, assemble)
Maybe somebody faced with such issues?
Thank you!
