cancel
Showing results for 
Search instead for 
Did you mean: 

NetIron CER 2048FX (IronWare : Version 6.0.0hT183 )

NetIron CER 2048FX (IronWare : Version 6.0.0hT183 )

cjgun
New Contributor
In the instructions for setting up

netiron-6300a-switchingguide.pdf and netiron-05900a-switchingguide.pdf
It is written to make LAG do the following:

Configuring the primary port for a LAG
In previous versions of the Multi-Service IronWare software, the lowest number port was assigned as
the primary port in a LAG or LACP configuration. In version 03.7.00 and later, the primary port must be
explicitly assigned using the primary-port command.
To designate the primary port for the static LAG "blue", use the following command.

device(config)# lag blue static
device(config-lag-blue)# primary-port 3/2
Syntax: [no] primary-port slot/port

Once a primary port has been configured for a LAG, all configurations that apply to the primary port
are applied to the other ports in the LAG.

Configuring load sharing type
Individual LAGs can be configured to perform load sharing over the ports in the LAG using either a
hash based or per packet method, as shown in the following.

device(config)# lag blue static
device(config-lag-blue)# trunk-type hash-based
Syntax: [no] trunk-type hash-based | per-packet

my config:

lag "BRASDownlink" dynamic id 7
ports ethernet 1/41 to 1/42
primary-port 1/41
deploy
port-name "BRAStoP09" ethernet 1/41
port-name "BRAStoP10" ethernet 1/42
!

I do not have such teams. Who knows why?
Only these:

SSH@NetIron CER 2048FX(config-lag-BRASDownlink)
acl-mirror-port
clear
cls
deploy
disable
enable
end
exit
force-primary-port-mac-use
lacp-port-priority
lacp-timeout
monitor
no
physical-port
port-name
ports
primary-port
quit
sflow-forwarding
sflow-subsampling
show
trunk-threshold
update-lag-name
write
7 REPLIES 7

Michael_Morey
Extreme Employee


That is correct. The CER is set to Hash-Based by default and this command is only available on the Chassis based systems.
Michael Morey
Principal Technical Support Engineer
Extreme Networks

cjgun
New Contributor


SSH@NetIron CER 2048FX#sh lag BRASDownlink
Total number of LAGs : 4, 100/40g : 0
Total number of deployed LAGs : 4, 100/40g : 0
Total number of trunks created : 4 (60 available), 100/40g : 0 (0 available)
LACP System Priority / ID :1 / 748e.f862.ca01
LACP Long timeout :90, default: 90
LACP Short timeout :3, default: 3

=== LAG "BRASDownlink" ID 7 (dynamic Deployed) ===
LAG Configuration:
Ports: e 1/41 to 1/42
Port Count: 2
Primary Port: 1/41
Trunk Type: hash-based
forward_all_protocol: Disabled
LACP Key: 103

That is, I can not change to other options?

If I upload another firmware, for example XMR-MLX/06000g

Supported devices for R06.0.00g
The following devices are supported in this release:
ExtremeRouting XMR Series
ExtremeRouting MLX Series
ExtremeSwitching CES 2000 Series
ExtremeRouting CER 2000 Series
CER 2048FX

joergkost
Contributor II
If I remember correctly, this command is only available on the XMR/MLX/MLXE, the CER/CES is hash-based by default.
GTM-P2G8KFN