This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Extreme Networks
- Community List
- Switching & Routing
- Data Center (VDX)
- RE: Confirm how to configure logical-chassis mode
Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
Confirm how to configure logical-chassis mode
Confirm how to configure logical-chassis mode
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
11-28-2021 09:36 PM
Hi I'd like to confirm the correct command to configure a VDX6740 firmware 7.2.0c.
I read in some older doco switch# vcs vcsid 1 rbridge-id 2 logical-chassis enable but this is not available and I can't recall the correct syntax and mode to execute this.
Thank you.
I read in some older doco switch# vcs vcsid 1 rbridge-id 2 logical-chassis enable but this is not available and I can't recall the correct syntax and mode to execute this.
Thank you.
7 REPLIES 7
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
11-29-2021 10:05 PM
In 7.0.x, the command is the same as the one you posted in your first post:
vcs vcsid 1 rbridge-id 2 logical-chassis enable
vcs vcsid 1 rbridge-id 2 logical-chassis enable
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-02-2021 10:52 PM
Thanks for the info Truyen.
Something's gone south with the firmware downgrade, I'm now in a bootloop on the switches. I'm getting an output of the boot process ATM to post here.
Something's gone south with the firmware downgrade, I'm now in a bootloop on the switches. I'm getting an output of the boot process ATM to post here.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-02-2021 11:09 PM
the boot up messages attached.-------------------------------------------
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.12.03 14:45:35 =~=~=~=~=~=~=~=~=~=~=~=
BootROM version: 1.0.76
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
CCB:749.700 MHz,
DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
FMAN1: 374.850 MHz
PME: 374.850 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 131
Board: P3041 CASTOR, 36-bit Addressing
reset reason was 0x00000001: Power Up
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
FSL_ERRATUM_DDR_A003 workaround applied
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
MMK configuring pit regs
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 1 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
158 bytes read
Image: [uImage]
Image: [hv.uImage]
Image: [silkworm.dtb]
Image: [silkworm_hct.dtb]
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 473624 Bytes = 462.5 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff22b ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
[0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
Brocade PB device tree:brocade,SILKWORM_PB
Got liodn 125
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
USB:
Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0
Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
Register 10011 NbrPorts 1
hv scanning bus for usb devices... 2 USB Device(s) found
[0] watchdog enabled with period 38
HV> Hypervisor scanning bus for storage devices...
HV> ========Storage Device Details==========
HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
HV> 1 HV Storage Device(s) found
HV> Init hypervisor timer init_timer:8
HV> [1] watchdog enabled with period 38
[2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [2] Virtual Storage thread=7e22d210
HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
HV>
part_start 2 2
dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
part2 STANDBY
HV>
part_start 0 2
HV>
dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] Clearing standby console log
HV> patch_pcie_msi_guest_node:set p2-linux msi0
HV> patch_pcie_msi_guest_node: set msi-address-64 f0000740
HV> b [0] loading binary image from 0x79fff000 to 0x3000000
HV> [2] loading binary image from 0x79fff000 to 0x3000000
[0] Loading uImage from 0x78000000 to 0
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
Using /devices/qman property 'fsl,qman-fqd'
it's a 'zero-pma', not zeroing from s/w
Using /devices/qman property 'fsl,qman-pfdr'
Qman ver:0a01,01,02
Treating Qman ver:01,02 as 0x0101
-> DMA enabled
[silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
network namespace NR (VRF) started
PCI_PROBE_DEVTREE
PCI_PROBE_DEVTREE
Qman registered for failover, is currently active
Qman err interrupt handler present
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1020000:c101e000 (0:0,v0101)
Qman portal initialised, cpu 0
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1028000:c1026000 (1:1,v0101)
Qman portal initialised, cpu 1
before calling: qman_release_fqid_range 512:256
Qman: FQID allocator includes range 512:256
Qman driver initialised
mmod_sysctl_inited: 1
***** pcie_portdrv_init: active completed
cpu1/1: failover_register() - registering notifiers...
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
gtg_init:Coldboot case
gtg_init(1):Ring bf4f6800 Peer Ring becf6800
Uboot wdt counter value: 0
VSD Created with major number vsd_probe = 254
disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
HV>
create_new_partition_table part_no 0 no_of_parts 2
HV> INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is sw0
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
Automatic Power-Up Self Tests...
1. DH...successful
2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
a. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6. HASH and HMAC tests...
a. SHA-1 hash...successful
b. SHA-256 hash...successful
c. SHA-384 hash...successful
d. SHA-512 hash...successful
e. HMAC-SHA-1 hash...successful
f. HMAC-SHA-224 hash...successful
g. HMAC-SHA-256 hash...successful
h. HMAC-SHA-384 hash...successful
i. HMAC-SHA-512 hash...successful
7. Zero-ization...Successful
8. ECDSA ...successful
9. ECDH ...successful
10. TLS KDF 1.0...successful
10a. TLS KDF 1.2...successful
11. SSH KDF...successful
sysmodAttach open failed: No such device or address
sysmodAttach open failed: No such device or address
system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful
All tests completed with 0 errors
GTG Peer GOS reset
(none)
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: WM reset
Found 1(threshold 5) abnormal reboots within 5000 seconds window(threshold)
KernelSpace rastrace_register
DCM MODE:0x0
SWBD module launch ... Fri Dec 3 03:10:30 GMT 2021
CPLD INIT DONE
SEEPROM Read Done!
Cobra rev B found
Info: panic dump has been initialized!
Starting HASM ... Fri Dec 3 03:10:47 GMT 2021
LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
Global Fan Direction: Port Side EXHAUST
Network OS (sw0)
sw0 console login: Castor: PCIe Err handler init plat_pci_init[800]
bhpc_irq_init: Using default device map. Size 10
bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
Starting Dcmd ... Fri Dec 3 03:10:50 GMT 2021
server starting
Restoring DCM database2048 indexes lost
.free list corrupted, idx 651 already assigned!
.tp_register, got none fss tp handle=10000001h
2021/12/03-03:10:55, [HSL-1012], 1, INFO, VDX6740, Interface lo is link up
2021/12/03-03:10:55, [HSL-1012], 2, INFO, VDX6740, Interface eth0 is link up
2021/12/03-03:10:55, [HSL-1012], 3, INFO, VDX6740, Interface eth1 is link up
2021/12/03-03:10:55, [HASM-1004], 4, INFO, VDX6740, Processor reloaded - Reset.
.....done
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [3] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
HV> [2] loading binary image from 0x79fff000 to 0x3000000
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> GTG Peer GOS reset
waiting for server to shut down............................... done
server stopped
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [3] Hypervisor Resetting due to: hcall_system_reset
[3]
Hypervisor Reset Flush:
HV>
BootROM version: 1.0.76
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
CCB:749.700 MHz,
DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
FMAN1: 374.850 MHz
PME: 374.850 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 131
Board: P3041 CASTOR, 36-bit Addressing
reset reason was 0x00000002: CPU request
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
FSL_ERRATUM_DDR_A003 workaround applied
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
MMK configuring pit regs
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 1 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
158 bytes read
Image: [uImage]
Image: [hv.uImage]
Image: [silkworm.dtb]
Image: [silkworm_hct.dtb]
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 473624 Bytes = 462.5 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff22b ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
[0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
Brocade PB device tree:brocade,SILKWORM_PB
Got liodn 125
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
USB:
Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0
Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
Register 10011 NbrPorts 1
hv scanning bus for usb devices... 2 USB Device(s) found
[0] watchdog enabled with period 38
HV> Hypervisor scanning bus for storage devices...
HV> ========Storage Device Details==========
HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
HV> 1 HV Storage Device(s) found
HV> Init hypervisor timer init_timer:8
HV> [1] watchdog enabled with period 38
[2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [2] Virtual Storage thread=7e22d210
HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
HV>
part_start 2 2
dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
part2 STANDBY
HV>
part_start 0 2
HV>
dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] Clearing standby console log
HV> patch_pcie_msi_guest_node:set p2-linux msi0
HV> b patch_pcie_msi_guest_node: set msi-address-64 f0000740
HV> [0] loading binary image from 0x79fff000 to 0x3000000
HV> [2] loading binary image from 0x79fff000 to 0x3000000
[0] Loading uImage from 0x78000000 to 0
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
Using /devices/qman property 'fsl,qman-fqd'
it's a 'zero-pma', not zeroing from s/w
Using /devices/qman property 'fsl,qman-pfdr'
Qman ver:0a01,01,02
Treating Qman ver:01,02 as 0x0101
-> DMA enabled
[silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
network namespace NR (VRF) started
PCI_PROBE_DEVTREE
PCI_PROBE_DEVTREE
Qman registered for failover, is currently active
Qman err interrupt handler present
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1020000:c101e000 (0:0,v0101)
Qman portal initialised, cpu 0
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1028000:c1026000 (1:1,v0101)
Qman portal initialised, cpu 1
before calling: qman_release_fqid_range 512:256
Qman: FQID allocator includes range 512:256
Qman driver initialised
mmod_sysctl_inited: 1
***** pcie_portdrv_init: active completed
cpu0/0: failover_register() - registering notifiers...
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
gtg_init:Coldboot case
gtg_init(1):Ring bf4f6800 Peer Ring becf6800
Uboot wdt counter value: 0
VSD Created with major number vsd_probe = 254
disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
HV>
create_new_partition_table part_no 0 no_of_parts 2
HV> INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is sw0
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
Automatic Power-Up Self Tests...
1. DH...successful
2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
a. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6. HASH and HMAC tests...
a. SHA-1 hash...successful
b. SHA-256 hash...successful
c. SHA-384 hash...successful
d. SHA-512 hash...successful
e. HMAC-SHA-1 hash...successful
f. HMAC-SHA-224 hash...successful
g. HMAC-SHA-256 hash...successful
h. HMAC-SHA-384 hash...successful
i. HMAC-SHA-512 hash...successful
7. Zero-ization...Successful
8. ECDSA ...successful
9. ECDH ...successful
10. TLS KDF 1.0...successful
10a. TLS KDF 1.2...successful
11. SSH KDF...successful
sysmodAttach open failed: No such device or address
sysmodAttach open failed: No such device or address
system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful
All tests completed with 0 errors
GTG Peer GOS reset
(none)
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: WM reset
Found 2(threshold 5) abnormal reboots within 5000 seconds window(threshold)
KernelSpace rastrace_register
DCM MODE:0x0
SWBD module launch ... Fri Dec 3 03:17:28 GMT 2021
CPLD INIT DONE
SEEPROM Read Done!
Cobra rev B found
Info: panic dump has been initialized!
Starting HASM ... Fri Dec 3 03:17:46 GMT 2021
LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
Network OS (sw0)
sw0 console login: Global Fan Direction: Port Side EXHAUST
Castor: PCIe Err handler init plat_pci_init[800]
bhpc_irq_init: Using default device map. Size 10
bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
Starting Dcmd ... Fri Dec 3 03:17:51 GMT 2021
tp_register, got none fss tp handle=10000001h
2021/12/03-03:17:53, [HSL-1012], 5, INFO, VDX6740, Interface lo is link up
2021/12/03-03:17:53, [HSL-1012], 6, INFO, VDX6740, Interface eth0 is link up
2021/12/03-03:17:53, [HSL-1012], 7, INFO, VDX6740, Interface eth1 is link up
2021/12/03-03:17:53, [HASM-1004], 8, INFO, VDX6740, Processor reloaded - Reset.
server starting
Restoring DCM database...done
Network OS (sw0)
sw0 console login: admin
Password:
2021/12/03-03:18:22, [SEC-1206], 9, SW/0 | Active, INFO, sw0, Login information: User [admin] Last Successful Login Time : Fri Dec 3 01:08:31 2021
.
Error: Network OS is not ready. Please login later.
2021/12/03-03:18:23, [SEC-3022], 10, SW/0 | Active, INFO, sw0, Event: logout, Status: success, Info: Successful logout by user [admin].
Network OS (sw0)
sw0 console login:
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [3] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
HV> [2] loading binary image from 0x79fff000 to 0x3000000
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> GTG Peer GOS reset
waiting for server to shut down........................ done
server stopped
Fri Dec 3 03:23:28 GMT 2021 :: Confd: Waiting for Dcmd to become ready...
Services starting COLD recovery
CHASSIS RECOV_ACTIVE
Activating Route Profile [RTPROFILE_TYPE_DEFAULT], ecmp [0]
Activating HW Profile [HWPROFILE_TYPE_DEFAULT]
Activating KAP Profile [DEFAULT]
SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
dcm init successful
Confd: No need to wait for Ccmd...
Fri Dec 3 03:23:43 GMT 2021 :: Triggering confd load phase1 after waiting for 10 secs
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> Passed :: register_for_publisher_notification for MSG_TNL_GW_CONF_NOTIFY passed for NSMD.
Subsribed successfully for NSMPORTDECFGMSG in rmond
radv trace initialization succeeded.
srm trace initialization succeeded.
arp trace initialization succeeded.
vrrp_tha_init: regdone handle 1
ARP trace init Successful
VRRP_tha_Init: stage 1 done
ribmgr trace initialization succeeded.
pcap_master_init - sm is NULL after ha_calloc
rps trace initialization succeeded.
[3] Hypervisor Resetting due to: hcall_system_reset
++++++++++++++++++++++++++++++++++++++++++++++++++++
Current Mode of Op:interrupt Vs Thread State:0x2 blockPos:4
Current Active cookie Gos0:21917 Gos1:2168
Current Queued max cookie Gos0:21918 Gos1:2168
Guest sem info data 0x0 waitlist 0x0
++++++++++++++++++++++++++++++++++++++++++++++++++++
HV>
calling system reset from vs_thread_worker:
[2]
Hypervisor Reset Flush:
HV>
since guest is stopping don't accept any io:hcall_submit_aio
HV>
BootROM version: 1.0.76
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
CCB:749.700 MHz,
DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
FMAN1: 374.850 MHz
PME: 374.850 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 131
Board: P3041 CASTOR, 36-bit Addressing
reset reason was 0x00000002: CPU request
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
FSL_ERRATUM_DDR_A003 workaround applied
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
MMK configuring pit regs
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 1 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
158 bytes read
Image: [uImage]
Image: [hv.uImage]
Image: [silkworm.dtb]
Image: [silkworm_hct.dtb]
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 473624 Bytes = 462.5 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff22b ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
[0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
Brocade PB device tree:brocade,SILKWORM_PB
Got liodn 125
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
USB:
Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0
Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
Register 10011 NbrPorts 1
hv scanning bus for usb devices... 2 USB Device(s) found
[0] watchdog enabled with period 38
HV> Hypervisor scanning bus for storage devices...
HV> ========Storage Device Details==========
HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
HV> 1 HV Storage Device(s) found
HV> Init hypervisor timer init_timer:8
HV> [1] watchdog enabled with period 38
[2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [2] Virtual Storage thread=7e22d210
HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
HV>
part_start 2 2
dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
HV>
part2 STANDBY
HV>
part_start 0 2
HV>
dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] Clearing standby console log
patch_pcie_msi_guest_node:set p2-linux msi0
HV> patch_pcie_msi_guest_node: set msi-address-64 f0000740
HV> b [0] loading binary image from 0x79fff000 to 0x3000000
HV> [2] loading binary image from 0x79fff000 to 0x3000000
[0] Loading uImage from 0x78000000 to 0
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
Using /devices/qman property 'fsl,qman-fqd'
it's a 'zero-pma', not zeroing from s/w
Using /devices/qman property 'fsl,qman-pfdr'
Qman ver:0a01,01,02
Treating Qman ver:01,02 as 0x0101
-> DMA enabled
[silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
network namespace NR (VRF) started
PCI_PROBE_DEVTREE
PCI_PROBE_DEVTREE
Qman registered for failover, is currently active
Qman err interrupt handler present
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1020000:c101e000 (0:0,v0101)
Qman portal initialised, cpu 0
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1028000:c1026000 (1:1,v0101)
Qman portal initialised, cpu 1
before calling: qman_release_fqid_range 512:256
Qman: FQID allocator includes range 512:256
Qman driver initialised
mmod_sysctl_inited: 1
***** pcie_portdrv_init: active completed
cpu1/1: failover_register() - registering notifiers...
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
gtg_init:Coldboot case
gtg_init(1):Ring bf4f6800 Peer Ring becf6800
Uboot wdt counter value: 0
VSD Created with major number vsd_probe = 254
disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
HV>
create_new_partition_table part_no 0 no_of_parts 2
HV> INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is sw0
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
Automatic Power-Up Self Tests...
1. DH...successful
2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
a. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6. HASH and HMAC tests...
a. SHA-1 hash...successful
b. SHA-256 hash...successful
c. SHA-384 hash...successful
d. SHA-512 hash...successful
e. HMAC-SHA-1 hash...successful
f. HMAC-SHA-224 hash...successful
g. HMAC-SHA-256 hash...successful
h. HMAC-SHA-384 hash...successful
i. HMAC-SHA-512 hash...successful
7. Zero-ization...Successful
8. ECDSA ...successful
9. ECDH ...successful
10. TLS KDF 1.0...successful
10a. TLS KDF 1.2...successful
11. SSH KDF...successful
sysmodAttach open failed: No such device or address
sysmodAttach open failed: No such device or address
system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful
All tests completed with 0 errors
GTG Peer GOS reset
(none)
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: WM reset
Found 3(threshold 5) abnormal reboots within 5000 seconds window(threshold)
KernelSpace rastrace_register
DCM MODE:0x0
SWBD module launch ... Fri Dec 3 03:25:10 GMT 2021
CPLD INIT DONE
SEEPROM Read Done!
Cobra rev B found
Info: panic dump has been initialized!
Starting HASM ... Fri Dec 3 03:25:28 GMT 2021
LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
Global Fan Direction: Port Side EXHAUST
Network OS (sw0)
sw0 console login: Castor: PCIe Err handler init plat_pci_init[800]
bhpc_irq_init: Using default device map. Size 10
bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
Starting Dcmd ... Fri Dec 3 03:25:34 GMT 2021
tp_register, got none fss tp handle=10000001h
2021/12/03-03:25:35, [HSL-1012], 11, INFO, VDX6740, Interface lo is link up
2021/12/03-03:25:35, [HSL-1012], 12, INFO, VDX6740, Interface eth0 is link up
2021/12/03-03:25:35, [HSL-1012], 13, INFO, VDX6740, Interface eth1 is link up
2021/12/03-03:25:35, [HASM-1004], 14, INFO, VDX6740, Processor reloaded - Reset.
server starting
Restoring DCM database...done
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [2] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
HV> [2] loading binary image from 0x79fff000 to 0x3000000
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> GTG Peer GOS reset
waiting for server to shut down............
Network OS (sw0)
sw0 console login: ..admin
.Password: ..
.2021/12/03-03:29:47, [SEC-1206], 15, SW/0 | Active, INFO, sw0, Login information: User [admin] Last Successful Login Time : Fri Dec 3 03:18:22 2021
.
...Error: Network OS is not ready. Please login later.
.2021/12/03-03:29:51, [SEC-3022], 16, SW/0 | Active, INFO, sw0, Event: logout, Status: success, Info: Successful logout by user [admin].
Network OS (sw0)
sw0 console login: ...............
Original Message:
Sent: 12-02-2021 22:51
From: Russ
Subject: Confirm how to configure logical-chassis mode
Thanks for the info Truyen.
Something's gone south with the firmware downgrade, I'm now in a bootloop on the switches. I'm getting an output of the boot process ATM to post here.
Original Message:
Sent: 11-29-2021 22:05
From: Truyen Phan
Subject: Confirm how to configure logical-chassis mode
In 7.0.x, the command is the same as the one you posted in your first post:
vcs vcsid 1 rbridge-id 2 logical-chassis enable
Original Message:
Sent: 11-29-2021 18:48
From: Russ
Subject: Confirm how to configure logical-chassis mode
Thanks again, for reference what was the command to configure logical-chassis mode?
Original Message:
Sent: 11-29-2021 01:12
From: Truyen Phan
Subject: Confirm how to configure logical-chassis mode
You will need to downgrade to 7.0.x, then set the vcs mode to logical chassis, then upgrade.
Original Message:
Sent: 11-29-2021 01:03
From: Russ
Subject: Confirm how to configure logical-chassis mode
Hi thanks for you reply. When I was checking the status after applying the VCSID and RB ID the output indicated that the switch was in VCS Mode : Fabric Cluster and not logical-chassis.
Original Message:
Sent: 11-29-2021 00:55
From: Truyen Phan
Subject: Confirm how to configure logical-chassis mode
Hi Russ,
Starting NOS 7.1.x and higher, the only valid VCS mode is logical chassis which is enabled by default, so there's no need to configure logical-chassis enable anymore. You just need to set the VCS ID and RB ID.
Original Message:
Sent: 11-28-2021 21:36
From: Russ
Subject: Confirm how to configure logical-chassis mode
Hi I'd like to confirm the correct command to configure a VDX6740 firmware 7.2.0c.
I read in some older doco switch# vcs vcsid 1 rbridge-id 2 logical-chassis enable but this is not available and I can't recall the correct syntax and mode to execute this.
Thank you.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.12.03 14:45:35 =~=~=~=~=~=~=~=~=~=~=~=
BootROM version: 1.0.76
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
CCB:749.700 MHz,
DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
FMAN1: 374.850 MHz
PME: 374.850 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 131
Board: P3041 CASTOR, 36-bit Addressing
reset reason was 0x00000001: Power Up
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
FSL_ERRATUM_DDR_A003 workaround applied
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
MMK configuring pit regs
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 1 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
158 bytes read
Image: [uImage]
Image: [hv.uImage]
Image: [silkworm.dtb]
Image: [silkworm_hct.dtb]
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 473624 Bytes = 462.5 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff22b ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
[0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
Brocade PB device tree:brocade,SILKWORM_PB
Got liodn 125
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
USB:
Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0
Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
Register 10011 NbrPorts 1
hv scanning bus for usb devices... 2 USB Device(s) found
[0] watchdog enabled with period 38
HV> Hypervisor scanning bus for storage devices...
HV> ========Storage Device Details==========
HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
HV> 1 HV Storage Device(s) found
HV> Init hypervisor timer init_timer:8
HV> [1] watchdog enabled with period 38
[2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [2] Virtual Storage thread=7e22d210
HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
HV>
part_start 2 2
dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
part2 STANDBY
HV>
part_start 0 2
HV>
dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] Clearing standby console log
HV> patch_pcie_msi_guest_node:set p2-linux msi0
HV> patch_pcie_msi_guest_node: set msi-address-64 f0000740
HV> b [0] loading binary image from 0x79fff000 to 0x3000000
HV> [2] loading binary image from 0x79fff000 to 0x3000000
[0] Loading uImage from 0x78000000 to 0
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
Using /devices/qman property 'fsl,qman-fqd'
it's a 'zero-pma', not zeroing from s/w
Using /devices/qman property 'fsl,qman-pfdr'
Qman ver:0a01,01,02
Treating Qman ver:01,02 as 0x0101
-> DMA enabled
[silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
network namespace NR (VRF) started
PCI_PROBE_DEVTREE
PCI_PROBE_DEVTREE
Qman registered for failover, is currently active
Qman err interrupt handler present
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1020000:c101e000 (0:0,v0101)
Qman portal initialised, cpu 0
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1028000:c1026000 (1:1,v0101)
Qman portal initialised, cpu 1
before calling: qman_release_fqid_range 512:256
Qman: FQID allocator includes range 512:256
Qman driver initialised
mmod_sysctl_inited: 1
***** pcie_portdrv_init: active completed
cpu1/1: failover_register() - registering notifiers...
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
gtg_init:Coldboot case
gtg_init(1):Ring bf4f6800 Peer Ring becf6800
Uboot wdt counter value: 0
VSD Created with major number vsd_probe = 254
disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
HV>
create_new_partition_table part_no 0 no_of_parts 2
HV> INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is sw0
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
Automatic Power-Up Self Tests...
1. DH...successful
2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
a. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6. HASH and HMAC tests...
a. SHA-1 hash...successful
b. SHA-256 hash...successful
c. SHA-384 hash...successful
d. SHA-512 hash...successful
e. HMAC-SHA-1 hash...successful
f. HMAC-SHA-224 hash...successful
g. HMAC-SHA-256 hash...successful
h. HMAC-SHA-384 hash...successful
i. HMAC-SHA-512 hash...successful
7. Zero-ization...Successful
8. ECDSA ...successful
9. ECDH ...successful
10. TLS KDF 1.0...successful
10a. TLS KDF 1.2...successful
11. SSH KDF...successful
sysmodAttach open failed: No such device or address
sysmodAttach open failed: No such device or address
system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful
All tests completed with 0 errors
GTG Peer GOS reset
(none)
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: WM reset
Found 1(threshold 5) abnormal reboots within 5000 seconds window(threshold)
KernelSpace rastrace_register
DCM MODE:0x0
SWBD module launch ... Fri Dec 3 03:10:30 GMT 2021
CPLD INIT DONE
SEEPROM Read Done!
Cobra rev B found
Info: panic dump has been initialized!
Starting HASM ... Fri Dec 3 03:10:47 GMT 2021
LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
Global Fan Direction: Port Side EXHAUST
Network OS (sw0)
sw0 console login: Castor: PCIe Err handler init plat_pci_init[800]
bhpc_irq_init: Using default device map. Size 10
bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
Starting Dcmd ... Fri Dec 3 03:10:50 GMT 2021
server starting
Restoring DCM database2048 indexes lost
.free list corrupted, idx 651 already assigned!
.tp_register, got none fss tp handle=10000001h
2021/12/03-03:10:55, [HSL-1012], 1, INFO, VDX6740, Interface lo is link up
2021/12/03-03:10:55, [HSL-1012], 2, INFO, VDX6740, Interface eth0 is link up
2021/12/03-03:10:55, [HSL-1012], 3, INFO, VDX6740, Interface eth1 is link up
2021/12/03-03:10:55, [HASM-1004], 4, INFO, VDX6740, Processor reloaded - Reset.
.....done
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [3] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
HV> [2] loading binary image from 0x79fff000 to 0x3000000
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> GTG Peer GOS reset
waiting for server to shut down............................... done
server stopped
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [3] Hypervisor Resetting due to: hcall_system_reset
[3]
Hypervisor Reset Flush:
HV>
BootROM version: 1.0.76
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
CCB:749.700 MHz,
DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
FMAN1: 374.850 MHz
PME: 374.850 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 131
Board: P3041 CASTOR, 36-bit Addressing
reset reason was 0x00000002: CPU request
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
FSL_ERRATUM_DDR_A003 workaround applied
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
MMK configuring pit regs
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 1 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
158 bytes read
Image: [uImage]
Image: [hv.uImage]
Image: [silkworm.dtb]
Image: [silkworm_hct.dtb]
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 473624 Bytes = 462.5 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff22b ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
[0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
Brocade PB device tree:brocade,SILKWORM_PB
Got liodn 125
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
USB:
Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0
Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
Register 10011 NbrPorts 1
hv scanning bus for usb devices... 2 USB Device(s) found
[0] watchdog enabled with period 38
HV> Hypervisor scanning bus for storage devices...
HV> ========Storage Device Details==========
HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
HV> 1 HV Storage Device(s) found
HV> Init hypervisor timer init_timer:8
HV> [1] watchdog enabled with period 38
[2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [2] Virtual Storage thread=7e22d210
HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
HV>
part_start 2 2
dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
part2 STANDBY
HV>
part_start 0 2
HV>
dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] Clearing standby console log
HV> patch_pcie_msi_guest_node:set p2-linux msi0
HV> b patch_pcie_msi_guest_node: set msi-address-64 f0000740
HV> [0] loading binary image from 0x79fff000 to 0x3000000
HV> [2] loading binary image from 0x79fff000 to 0x3000000
[0] Loading uImage from 0x78000000 to 0
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
Using /devices/qman property 'fsl,qman-fqd'
it's a 'zero-pma', not zeroing from s/w
Using /devices/qman property 'fsl,qman-pfdr'
Qman ver:0a01,01,02
Treating Qman ver:01,02 as 0x0101
-> DMA enabled
[silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
network namespace NR (VRF) started
PCI_PROBE_DEVTREE
PCI_PROBE_DEVTREE
Qman registered for failover, is currently active
Qman err interrupt handler present
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1020000:c101e000 (0:0,v0101)
Qman portal initialised, cpu 0
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1028000:c1026000 (1:1,v0101)
Qman portal initialised, cpu 1
before calling: qman_release_fqid_range 512:256
Qman: FQID allocator includes range 512:256
Qman driver initialised
mmod_sysctl_inited: 1
***** pcie_portdrv_init: active completed
cpu0/0: failover_register() - registering notifiers...
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
gtg_init:Coldboot case
gtg_init(1):Ring bf4f6800 Peer Ring becf6800
Uboot wdt counter value: 0
VSD Created with major number vsd_probe = 254
disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
HV>
create_new_partition_table part_no 0 no_of_parts 2
HV> INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is sw0
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
Automatic Power-Up Self Tests...
1. DH...successful
2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
a. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6. HASH and HMAC tests...
a. SHA-1 hash...successful
b. SHA-256 hash...successful
c. SHA-384 hash...successful
d. SHA-512 hash...successful
e. HMAC-SHA-1 hash...successful
f. HMAC-SHA-224 hash...successful
g. HMAC-SHA-256 hash...successful
h. HMAC-SHA-384 hash...successful
i. HMAC-SHA-512 hash...successful
7. Zero-ization...Successful
8. ECDSA ...successful
9. ECDH ...successful
10. TLS KDF 1.0...successful
10a. TLS KDF 1.2...successful
11. SSH KDF...successful
sysmodAttach open failed: No such device or address
sysmodAttach open failed: No such device or address
system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful
All tests completed with 0 errors
GTG Peer GOS reset
(none)
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: WM reset
Found 2(threshold 5) abnormal reboots within 5000 seconds window(threshold)
KernelSpace rastrace_register
DCM MODE:0x0
SWBD module launch ... Fri Dec 3 03:17:28 GMT 2021
CPLD INIT DONE
SEEPROM Read Done!
Cobra rev B found
Info: panic dump has been initialized!
Starting HASM ... Fri Dec 3 03:17:46 GMT 2021
LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
Network OS (sw0)
sw0 console login: Global Fan Direction: Port Side EXHAUST
Castor: PCIe Err handler init plat_pci_init[800]
bhpc_irq_init: Using default device map. Size 10
bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
Starting Dcmd ... Fri Dec 3 03:17:51 GMT 2021
tp_register, got none fss tp handle=10000001h
2021/12/03-03:17:53, [HSL-1012], 5, INFO, VDX6740, Interface lo is link up
2021/12/03-03:17:53, [HSL-1012], 6, INFO, VDX6740, Interface eth0 is link up
2021/12/03-03:17:53, [HSL-1012], 7, INFO, VDX6740, Interface eth1 is link up
2021/12/03-03:17:53, [HASM-1004], 8, INFO, VDX6740, Processor reloaded - Reset.
server starting
Restoring DCM database...done
Network OS (sw0)
sw0 console login: admin
Password:
2021/12/03-03:18:22, [SEC-1206], 9, SW/0 | Active, INFO, sw0, Login information: User [admin] Last Successful Login Time : Fri Dec 3 01:08:31 2021
.
Error: Network OS is not ready. Please login later.
2021/12/03-03:18:23, [SEC-3022], 10, SW/0 | Active, INFO, sw0, Event: logout, Status: success, Info: Successful logout by user [admin].
Network OS (sw0)
sw0 console login:
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [3] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
HV> [2] loading binary image from 0x79fff000 to 0x3000000
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> GTG Peer GOS reset
waiting for server to shut down........................ done
server stopped
Fri Dec 3 03:23:28 GMT 2021 :: Confd: Waiting for Dcmd to become ready...
Services starting COLD recovery
CHASSIS RECOV_ACTIVE
Activating Route Profile [RTPROFILE_TYPE_DEFAULT], ecmp [0]
Activating HW Profile [HWPROFILE_TYPE_DEFAULT]
Activating KAP Profile [DEFAULT]
SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
dcm init successful
Confd: No need to wait for Ccmd...
Fri Dec 3 03:23:43 GMT 2021 :: Triggering confd load phase1 after waiting for 10 secs
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> Passed :: register_for_publisher_notification for MSG_TNL_GW_CONF_NOTIFY passed for NSMD.
Subsribed successfully for NSMPORTDECFGMSG in rmond
radv trace initialization succeeded.
srm trace initialization succeeded.
arp trace initialization succeeded.
vrrp_tha_init: regdone handle 1
ARP trace init Successful
VRRP_tha_Init: stage 1 done
ribmgr trace initialization succeeded.
pcap_master_init - sm is NULL after ha_calloc
rps trace initialization succeeded.
[3] Hypervisor Resetting due to: hcall_system_reset
++++++++++++++++++++++++++++++++++++++++++++++++++++
Current Mode of Op:interrupt Vs Thread State:0x2 blockPos:4
Current Active cookie Gos0:21917 Gos1:2168
Current Queued max cookie Gos0:21918 Gos1:2168
Guest sem info data 0x0 waitlist 0x0
++++++++++++++++++++++++++++++++++++++++++++++++++++
HV>
calling system reset from vs_thread_worker:
[2]
Hypervisor Reset Flush:
HV>
since guest is stopping don't accept any io:hcall_submit_aio
HV>
BootROM version: 1.0.76
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
CCB:749.700 MHz,
DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
FMAN1: 374.850 MHz
PME: 374.850 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 131
Board: P3041 CASTOR, 36-bit Addressing
reset reason was 0x00000002: CPU request
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
FSL_ERRATUM_DDR_A003 workaround applied
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
MMK configuring pit regs
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 1 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... Manufacturer u-boot
Product EHCI Host Controller
SerialNumber
Manufacturer Generic
Product Flash Card Reader
SerialNumber 000000225001
2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 2
Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
158 bytes read
Image: [uImage]
Image: [hv.uImage]
Image: [silkworm.dtb]
Image: [silkworm_hct.dtb]
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 473624 Bytes = 462.5 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff22b ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
[0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
Brocade PB device tree:brocade,SILKWORM_PB
Got liodn 125
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
USB:
Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0
Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
Register 10011 NbrPorts 1
hv scanning bus for usb devices... 2 USB Device(s) found
[0] watchdog enabled with period 38
HV> Hypervisor scanning bus for storage devices...
HV> ========Storage Device Details==========
HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
HV> 1 HV Storage Device(s) found
HV> Init hypervisor timer init_timer:8
HV> [1] watchdog enabled with period 38
[2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [2] Virtual Storage thread=7e22d210
HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
HV>
part_start 2 2
dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
[vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
HV>
part2 STANDBY
HV>
part_start 0 2
HV>
dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV>
[vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] Clearing standby console log
patch_pcie_msi_guest_node:set p2-linux msi0
HV> patch_pcie_msi_guest_node: set msi-address-64 f0000740
HV> b [0] loading binary image from 0x79fff000 to 0x3000000
HV> [2] loading binary image from 0x79fff000 to 0x3000000
[0] Loading uImage from 0x78000000 to 0
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
Using /devices/qman property 'fsl,qman-fqd'
it's a 'zero-pma', not zeroing from s/w
Using /devices/qman property 'fsl,qman-pfdr'
Qman ver:0a01,01,02
Treating Qman ver:01,02 as 0x0101
-> DMA enabled
[silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
network namespace NR (VRF) started
PCI_PROBE_DEVTREE
PCI_PROBE_DEVTREE
Qman registered for failover, is currently active
Qman err interrupt handler present
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1020000:c101e000 (0:0,v0101)
Qman portal initialised, cpu 0
Treating Qman portal ver:0x0102 as 0x0101
Qman portal at c1028000:c1026000 (1:1,v0101)
Qman portal initialised, cpu 1
before calling: qman_release_fqid_range 512:256
Qman: FQID allocator includes range 512:256
Qman driver initialised
mmod_sysctl_inited: 1
***** pcie_portdrv_init: active completed
cpu1/1: failover_register() - registering notifiers...
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
gtg_init:Coldboot case
gtg_init(1):Ring bf4f6800 Peer Ring becf6800
Uboot wdt counter value: 0
VSD Created with major number vsd_probe = 254
disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
HV>
create_new_partition_table part_no 0 no_of_parts 2
HV> INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is sw0
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
Automatic Power-Up Self Tests...
1. DH...successful
2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
a. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6. HASH and HMAC tests...
a. SHA-1 hash...successful
b. SHA-256 hash...successful
c. SHA-384 hash...successful
d. SHA-512 hash...successful
e. HMAC-SHA-1 hash...successful
f. HMAC-SHA-224 hash...successful
g. HMAC-SHA-256 hash...successful
h. HMAC-SHA-384 hash...successful
i. HMAC-SHA-512 hash...successful
7. Zero-ization...Successful
8. ECDSA ...successful
9. ECDH ...successful
10. TLS KDF 1.0...successful
10a. TLS KDF 1.2...successful
11. SSH KDF...successful
sysmodAttach open failed: No such device or address
sysmodAttach open failed: No such device or address
system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful
All tests completed with 0 errors
GTG Peer GOS reset
(none)
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: WM reset
Found 3(threshold 5) abnormal reboots within 5000 seconds window(threshold)
KernelSpace rastrace_register
DCM MODE:0x0
SWBD module launch ... Fri Dec 3 03:25:10 GMT 2021
CPLD INIT DONE
SEEPROM Read Done!
Cobra rev B found
Info: panic dump has been initialized!
Starting HASM ... Fri Dec 3 03:25:28 GMT 2021
LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
Global Fan Direction: Port Side EXHAUST
Network OS (sw0)
sw0 console login: Castor: PCIe Err handler init plat_pci_init[800]
bhpc_irq_init: Using default device map. Size 10
bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
Starting Dcmd ... Fri Dec 3 03:25:34 GMT 2021
tp_register, got none fss tp handle=10000001h
2021/12/03-03:25:35, [HSL-1012], 11, INFO, VDX6740, Interface lo is link up
2021/12/03-03:25:35, [HSL-1012], 12, INFO, VDX6740, Interface eth0 is link up
2021/12/03-03:25:35, [HSL-1012], 13, INFO, VDX6740, Interface eth1 is link up
2021/12/03-03:25:35, [HASM-1004], 14, INFO, VDX6740, Processor reloaded - Reset.
server starting
Restoring DCM database...done
disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
HV>
create_new_partition_table part_no 2 no_of_parts 2
HV> [2] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
HV> [2] loading binary image from 0x79fff000 to 0x3000000
HV> [2] Loading uImage from 0x78000000 to 0
HV> [2] branching to guest p2-linux, 2 cpus
HV> GTG Peer GOS reset
waiting for server to shut down............
Network OS (sw0)
sw0 console login: ..admin
.Password: ..
.2021/12/03-03:29:47, [SEC-1206], 15, SW/0 | Active, INFO, sw0, Login information: User [admin] Last Successful Login Time : Fri Dec 3 03:18:22 2021
.
...Error: Network OS is not ready. Please login later.
.2021/12/03-03:29:51, [SEC-3022], 16, SW/0 | Active, INFO, sw0, Event: logout, Status: success, Info: Successful logout by user [admin].
Network OS (sw0)
sw0 console login: ...............
Original Message:
Sent: 12-02-2021 22:51
From: Russ
Subject: Confirm how to configure logical-chassis mode
Thanks for the info Truyen.
Something's gone south with the firmware downgrade, I'm now in a bootloop on the switches. I'm getting an output of the boot process ATM to post here.
Original Message:
Sent: 11-29-2021 22:05
From: Truyen Phan
Subject: Confirm how to configure logical-chassis mode
In 7.0.x, the command is the same as the one you posted in your first post:
vcs vcsid 1 rbridge-id 2 logical-chassis enable
Original Message:
Sent: 11-29-2021 18:48
From: Russ
Subject: Confirm how to configure logical-chassis mode
Thanks again, for reference what was the command to configure logical-chassis mode?
Original Message:
Sent: 11-29-2021 01:12
From: Truyen Phan
Subject: Confirm how to configure logical-chassis mode
You will need to downgrade to 7.0.x, then set the vcs mode to logical chassis, then upgrade.
Original Message:
Sent: 11-29-2021 01:03
From: Russ
Subject: Confirm how to configure logical-chassis mode
Hi thanks for you reply. When I was checking the status after applying the VCSID and RB ID the output indicated that the switch was in VCS Mode : Fabric Cluster and not logical-chassis.
Original Message:
Sent: 11-29-2021 00:55
From: Truyen Phan
Subject: Confirm how to configure logical-chassis mode
Hi Russ,
Starting NOS 7.1.x and higher, the only valid VCS mode is logical chassis which is enabled by default, so there's no need to configure logical-chassis enable anymore. You just need to set the VCS ID and RB ID.
Original Message:
Sent: 11-28-2021 21:36
From: Russ
Subject: Confirm how to configure logical-chassis mode
Hi I'd like to confirm the correct command to configure a VDX6740 firmware 7.2.0c.
I read in some older doco switch# vcs vcsid 1 rbridge-id 2 logical-chassis enable but this is not available and I can't recall the correct syntax and mode to execute this.
Thank you.
