Show port Utilization command
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-14-2014 05:19 PM
Hello, I have a question regarding the way Extreme switches display traffic direction on its ports.
We have a GPS/weather-receiver station connected to one of our switches (Summit X450e) that transmit data only one way (from the GPS unit to our network). Thus, I'd expected to see traffic going 'into' the switchport and nothing else. However, when I issue a 'sh port 1:44 utilization' command I get the total opposite, with traffic being transmitted 'from' the switchport instead of 'to' the switchport. Am I reading this wrong? Please see output below:
Slot-1 MySwitch# sh por 1:44 utilization
Link Utilization Averages Thu Aug 14 14:17:13 2014Port Link Rx Peak Rx Tx Peak Tx
State pkts/sec pkts/sec pkts/sec pkts/sec
================================================================================
GPS_Unit A 0 0 7 10
Any input is appreciated. Thanks.
We have a GPS/weather-receiver station connected to one of our switches (Summit X450e) that transmit data only one way (from the GPS unit to our network). Thus, I'd expected to see traffic going 'into' the switchport and nothing else. However, when I issue a 'sh port 1:44 utilization' command I get the total opposite, with traffic being transmitted 'from' the switchport instead of 'to' the switchport. Am I reading this wrong? Please see output below:
Slot-1 MySwitch# sh por 1:44 utilization
Link Utilization Averages Thu Aug 14 14:17:13 2014Port Link Rx Peak Rx Tx Peak Tx
State pkts/sec pkts/sec pkts/sec pkts/sec
================================================================================
GPS_Unit A 0 0 7 10
Any input is appreciated. Thanks.
13 REPLIES 13
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-15-2014 05:00 AM
Well, that makes sense except that the Rx packet count is 0. I'm only seeing transmits on that port
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-15-2014 05:00 AM
Hi Alex,
I'd say that this is totally fine, because broadcasts for example are transmitted out of every port - including the one where you've connected your GPS unit. Basically you should see traffic from the switch to the end device on every port that is active.
The switch does not know that your GPS unit does not want to receive traffic. If you want to make sure that no traffic reaches the GPS unit, you have to write an ACL denying every bit of traffic that goes to the GPS unit.
Hope that helps,
Robert
I'd say that this is totally fine, because broadcasts for example are transmitted out of every port - including the one where you've connected your GPS unit. Basically you should see traffic from the switch to the end device on every port that is active.
The switch does not know that your GPS unit does not want to receive traffic. If you want to make sure that no traffic reaches the GPS unit, you have to write an ACL denying every bit of traffic that goes to the GPS unit.
Hope that helps,
Robert
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-14-2014 11:38 PM
Ok Jason, I will try to mirror the port where the GPS is connected. Hopefully those Wireshark filters will reveal more.. thanks.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-14-2014 11:38 PM
Alex Is ther a way that you can place a repeater between the port and the station and then place a sniffer ( Wireshark is free) and capture traffic I would the note the MAC address of the station and type Eth.addr == xx-xx-xx-xx-xx-xx Then reveiw the traffic Another step !Eth.addr == xx-xx-xx-xx-xx-xx And review that traffic Please relay your findings Or just configure mirror Oh My God to a drat port and run the same commands Thanks Jason
