2016-07-11: New GTAC Knowledge Articles July 3 - 9, 2016

  • 0
  • 2
  • Article
  • Updated 2 years ago
Here are the new articles that were published July 03 - July 09, 2016 in GTAC Knowledge:

Sunday, July 03, 2016:
none

Monday, July 04, 2016:
Enabling egress VMAN CEP filtering on a CEP port drops untagged traffic.

Tuesday, July 05, 2016:
How to configure primary and secondary default routes with ICMP probe for dual connected ISP routes on S/K/7100-Series
How to set a 40G port to 4x10G
How to secure OSPF with an MD5 password in XOS
How long has the AP 3610 had been in production?
Providing a non-existing file name to "run script" indicates only .xsf files can be run
SSH client stops working after executing a Python script
Switch indicates unsaved configuration changes after reboot
How to change syslog location in Netsight
Windows 10 being assigned policy by CEP
Unable to create L3 egress forwarding object for unit 0 - L3 table full log
After disabling mpls exp replacement, exp examination is not happening properly

Wednesday, July 06, 2016:
How do I remove a radius server from the Wireless Controler
Network being flooded with Multicast packets causing Network outages
What are the recommended settings for Ascom VOIP Phones
S-Series Log Reports OSPF Duplicate Router ID
Siem: Emails sent by the SIEM contain a link to a report that is incorrect
Connectivity issues with static LAG
Netsight Alarm indicating the Switch is Receiving an ARP with bad target IP address 255.255.255.0.
Intel AC 7260 client will get stuck forever when it roams to one area without Wi-Fi coverage
How to reset the iflastchange counter for an interface
APs are not forming a back-up tunnel on a paired Topology when the AP registration is disabled on one Wireless appliance Topology.
Can I use a WDS Radio for Client Traffic?
How to configure log filter events to show spanning tree topology changes notifications
SecureStack VLAN communication issue after changing VLAN assignment policy
5m SFP+ passive copper cables does not work
Delay in the multicast traffic while a new stream is received in a PIM Spasrse mode enabled network

Thursday, July 07, 2016:
UPM script to calculate the number of bytes to a destination ip every 5 secs
Network Latency and Card reset on S-Series
K-Series Fabric Hardware Error Message During Boot

Friday, July 08, 2016:
Can the management port be used in mirroring configurations?
Support Portal user account unable to perform password reset for an existing account
40Gb, QSFP+ Parallel Single Mode (PSM), MPO connector, 10km SMF support

Saturday, July 09, 2016:
none
Photo of Thomas, Ken

Thomas, Ken, Alum

  • 4,368 Points 4k badge 2x thumb

Posted 2 years ago

  • 0
  • 2
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 50,004 Points 50k badge 2x thumb
Thanks for the update... ..

"How do I remove a radius server from the Wireless Controler"

Unfortunately that one doesn't describe what the title says.
If you want to remove a RADIUS from the controller that is done in > VNS > global > authentication.


-Ron
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 50,004 Points 50k badge 2x thumb
"Can I use a WDS Radio for Client Traffic?"

In my opinion that should be a "Yes" with the note that this will reduce the overall bandwidth on the link as the WDS SSID and Client Traffic SSID will share the same radio/frequency.
Photo of Drew C.

Drew C., Community Manager

  • 40,206 Points 20k badge 2x thumb
Thanks for the feedback, Ron!  We'll take a look at updating the articles.
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 50,004 Points 50k badge 2x thumb
back to the top.....
Photo of Jason

Jason, Employee

  • 3,608 Points 3k badge 2x thumb
Ron, thanks again for the feedback. I agree on the points you made for both articles -  these have been edited with accurate information!