ā07-03-2019 07:25 AM
ā07-03-2019 09:01 AM
Hi Ivan,
With this, you may be able to recover the AP, with a TFTP flash of the firmware however you'll need to open a support case as it requires access to the bootloader and Aerohive do not give out the password for this. If unsuccessful you'll have to RMA unfortunately.
ā07-03-2019 07:26 AM
U-Boot 2012.10 (Aug 21 2018 - 20:22:25)
I2C: ready
Wait.
Done.
DEV ID= 0000cf12
REV ID= 00000000
SKU ID = 0
OTP status: eca00018
MEMC 0 DDR speed = 800MHz
Log: ddr40_phy_init.c: Configuring DDR Controller PLLs
Log: offset = 0x18010800
Log: VCO_FREQ is 1600 which is greater than 1Ghz.
Log: DDR Phy PLL polling for lock
Log: DDR Phy PLL locked.
Log: ddr40_phy_init::DDR PHY step size calibration complete.
Log: ddr40_phy_init:: Virtual VttSetup onm CONNECT=0x01CF7FFF, OVERRIDE=0x00077FFF
Log: ddr40_phy_init:: Virtual Vtt Enabled
Log: DDR Controller PLL Configuration Complete
PHY register dump after DDR PHY init
PHY register dump after mode register write
DRAM: 512 MiB
WARNING: Caches not enabled
GPIO Init ... Done
Power Input Detection: POE AF, Drive GPIO17(USB 5V enable) success
NAND: NAND_FLASH_DEVICE_ID_ADDR = 18028194
Done that
(ONFI), W29N04GV, blocks per lun: 1000 lun count: 1
*WARNING* Invalid strap options for this NAND: page=1 type=2
Overriding invalid strap options: strap_type=2
128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND: chipsize
total 0 bad blocks,LIST:
now the up level will see a good flash chip no bad block which size is 20000000
before nvram partition, there are 0 bad blocks
512 MiB
Using default environment
In: serial
Out: serial
Err: serial
Unlocking L2 Cache ...Done
arm_clk=1000MHz, axi_clk=500MHz, apb_clk=250MHz, arm_periph_clk=500MHz
Net: Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC1 (0x18025000)
et0: ethHw_chipAttach: Chip ID: 0xcf12; phyaddr: 0x1e
bcm_robo_attach: devid: 0x53012
bcmiproc_eth-0
MAC address is f4ea:b500:9b00
NVRAM_MAGIC found at offset 700000
nvram_init: ret 1
Reset TPM chip...
Reset AUTH chip...
Hit any key to stop autoboot: 0
Hit any key to interrupt boot from flash: 0
Loading kernel from device 0: nand0 (offset 0x800000) ... done
Loading rootfs from device 0: nand0 (offset 0x1600000) ... done
## Booting kernel from Legacy Image at 01005000 ...
Image Name: Linux-3.16.36
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2327777 Bytes = 2.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02005000 ...
Image Name: uboot initramfs rootfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 30662656 Bytes = 29.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Power off two PHY...
Loading Kernel Image ... OK
OK
boot_prep_linux commandline: root=/dev/ram console=ttyS0,9600 ramdisk_size=70000 cache-sram-size=0x10000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
board_fixup: mem=512MB
L2C: platform provided aux values match the hardware, so have no effect. Please remove them.
L2C: platform provided aux values permit register corruption.
Mounting local file systems...
UBI device number 0, total 3256 LEBs (413433856 bytes, 394.3 MiB), available 75 LEBs (9523200 bytes, 9.1 MiB), LEB size 126976 bytes (124.0 KiB)
Updating system config database...
System config update complete.
kmpi: module license 'Aerohive Wireless Inc.' taints kernel.
Disabling lock debugging due to kernel taint
POE Input Detection -> AF
set attenuator GPIO 7b0f00->7b4f40
gmac_var_init: NAPI2_POLL mode
register snif device on interface eth0.
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 10.10.80.505_e5.1.2.3 (r659762)
register snif device on interface eth1.
eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 10.10.80.505_e5.1.2.3 (r659762)