New Documentation Published June 4th-10th!

[SamPirok]

Our support teams published 45 new articles last week! Check out the new titles below!

All

Who can obtain information regarding entitlement, assets, etc.? 

Campus Fabric Articles

How to use TPVM on a DVR Leaf node for packet capture 

Newly Configured SMLT/LACP Not Passing Traffic 

BIOS Connect, Remote BIOS, PXE Boot Unable To Receive DHCP Address and MAC Not Learning On Port 

Can Static Multicast ARP Entries and IGMP Be Used With NLB (Network Load Balancer) VOSS Implementati... 

Support of DCBX feature on VOSS 

VSP-7400: C-vid configuration on MLT not working after LACP is removed 

CloudIQ Pilot, Network Policy, Device Credentials not being applied 

ERS (BOSS): EDM not accessible 

ERS: Cannot perform VLAN changes on EAP enabled port 

XA 1400 Not Showing Under Router Templates In XIQ

Data Center Articles

EFA is not operational 

Drift in configuration port 0/2, however "efa fabric show" command shows the configuration in-sync 

After uninstalling EFA/XCO the previously existing fabric configuration remains on the SLX 

LACP blocks on multiple Port-Channels after single config change to one Port-Channel 

SLX 9150-48XT TX Discards 

How to configure SNMPV3 informs on SLX 

After upgrade to 7.4.1f errdumpall output contains IPC-5010 messages 

problem with BR-MLX-MR2-M standby down state 

EFA is not starting properly, and the pods are in Init state.

EXOS Articles

Unable to assign 10Gb Feature License to stack members via XIQ Cloud 

<Erro:POE.port_fault> Slot- x : Port x:x has encountered a fault condition 

10Gb License activation fails with "Error: Failed to enable feature PRD-5320-10G-8P. RMS failure" 

1G optics do not link up in 10G ports after reboot

Legacy Articles

Clients unable to connect to SSID after the AP has been up a few days 

Can you re-name APs in bulk on XIQ-Controller?

SD-WAN Articles

"Appliance Disk Full" alarm message in the orchestrator logs 

Only the egress direction is visible in my reporting 

How to reset the DHCP Lease on a Vrouter? 

Universal Articles

VSP (VOSS) Is there any plan to move to to PAE-MIB from Rapid City? 

VIM ports do not show up under Port Configuration in XIQ for 5520 

WiNG Articles

What lighttpd version is used by recent WiNG releases? 

Spectrum Analysis on NSIGHT does not work on ap410c-1 

WiNG - Can WiNG virtual controller APs adopt Universal APs such as AP305C, AP410C and AP510C APs? 

Steps on how to retire or decommission AirDefense appliance 

XIQ Articles

ExtremeCloud IQ (XIQ): AP510C/CX Deployment are Displaying 'discovering country code' and stuck at 9 

XIQ - Why am I getting a red serial number box when onboarding an AP? 

ACSP can't be initialized when Indonesia country code is in use 

XIQ support of legacy APs 

How to pull a client list by SSID 

ExtremeCloud IQ (XIQ): AP4000, AP5010's are stuck discovering country codes, 9% 

The current restrictions of Extreme Cloud IQ's 6GHz radio SSID assignment 

Lenovo 300e Chromebooks experiencing poor performance in wireless network 

IQVA to XIQ migration - Import Error 

XIQ - How to create wireless client count report

If you have any requests for new articles, please let us know! You can either comment on this post, or email me directly at community@extremenetworks.com.

[w1f1n00b]

Regarding this post for Chromebooks ( https://extremeportal.force.com/ExtrArticleDetail?an=000111723 )

UAPSD (Unscheduled Automatic Power Save Delivery) should be disabled.

Does anyone know where this setting is configured for Extreme XIQ

Also curious, when trying to pinpoint the cli command used for " A-MPDU (Aggregate MAC Protocol Data Unit) should be disabled." I've looked at delta config before and after checking this box

When checking after unchecking this box and saving the radio profile, this is the cli I'm seeing (This is with Mu-MIMO disabled)