Config download script does not appear in Inventory Manager DropDown-Menu

[Marco_Lorenz]

I'm trying to figure out an issue with download Extreme XOS Deviceconfigs via NetSight InventoryManager. The Device I want to backup is a Summit X440-Device with XOS 15.3.1.4-patch1-41 running on it. NetSight always tells File not Found. While searching this error I found:

https://extremeportal.force.com/ExtrArticleDetail?an=000077044

Now I want to build a script with@receive 15 in it. No Problem with that, but after I have copied this script to .../NetSight_Instal_path/NetSight/appdata/InventoryMgr/properties/devicefiles I cannot see the script in the DropDown-Menu of InventoryManager. The whole Server has already been restarted.

Anyone an idea?

Here is the script which has been saved as .txt and .cfg without success...

-- Use these scripts to manage Extreme XOS devices
name="ExtremeXOSReceive15 - TFTP"
desc="Extreme SSH/TFTP Scripts using VR-Default interface"
protocol=TFTP
--
separator=UNIX_FILE_SEPARATOR
advanced_script_support=true
-- Recheck script output for success even if there was an error.
perform_success_test_always=true
--
-----BEGIN SCRIPT "Configuration Upload"-----
save configuration primary
Y

@receive 15
save configuration as-script nms
@key y
@key %0d
@RECEIVEUNTIL 30 ".*done!.*"
@receive 15
%EXTR_DYNAMIC_COMMANDS%
@receive 15
exit
-----END SCRIPT-----
-----BEGIN SUCCESS "Configuration Upload"-----
Uploading.*done!
-----END SUCCESS-----
-----BEGIN FAILURE MAPPINGS "Configuration Upload"-----
Error: timeout=The device was unable to contact the TFTP server. Check that the TFTP server is running and connectivity is okay.
Network is unreachable=The device was unable to download the configuration. Check that the correct VR is being used.
.*to switch... failed=Backup of the configuration failed. Verify that the TFTP server is running and connectivity is okay.
-----END FAILURE MAPPINGS-----
--
-----BEGIN SCRIPT "Configuration Download"-----
save configuration primary
Y
%EXTR_DYNAMIC_COMMANDS%
@receive 10
use configuration primary
reboot
y
exit
-----END SCRIPT-----
-----BEGIN SUCCESS "Configuration Download"-----
Downloading.*(to switch|on.*MSM|on.*MM).+ done!
The selected configuration will take effect after the next switch reboot.
-----END SUCCESS-----
-----BEGIN FAILURE MAPPINGS "Configuration Download"-----
Error: timeout=The device was unable to contact the TFTP server. Check that the TFTP server is running and connectivity is okay.
Network is unreachable=The device was unable to download the configuration. Check that the correct VR is being used.
Downloading.*to switch... failed=Restore of the configuration failed. Verify that the TFTP server is running and connectivity is okay.
-----END FAILURE MAPPINGS-----
--
-----BEGIN SCRIPT "Firmware Download"-----
%SET_IMAGE_PARTITION_BEFORE_INSTALL%

@# Remove any debug files from internal-memory before upgrade
rm internal-memory *
@key y
@key %0d
@receive 15

download image %TFTP_IP% %RELATIVE_TARGET_FILE_PATH% vr "%VR_VAR%"
@key y
@COMMANDDONE 30
@key %0d
@COMMANDDONE 2
%SET_IMAGE_PARTITION_AFTER_INSTALL%
exit
@# Answer to Save Configuration?
@key y
-----END SCRIPT-----
-----BEGIN SUCCESS "Firmware Download"-----
Image installed successfully
-----END SUCCESS-----
-----BEGIN FAILURE MAPPINGS "Firmware Download"-----
Downloading to Switchexit=The device was unable to contact the tftp server. Verify the TFTP server is running and connectivity is okay.
tftp: sendto: Network is unreachable=The device was unable to download the image. Check that the correct VR is being used.
tftp: server error: (2) cannot access file=The device cannot access the image file. Please check the permissions of the file.
is not an Extreme Networks image=The file selected to be downloaded to the device is NOT an Extreme Networks image. Please select an appropriate image file.
Error: File could not be unwrapped=The image file selected is corrupt and cannot be downloaded.
Error: File is not properly formatted=The image file selected is not properly formatted.
Error: Illegal filename=The image filename is illegal. Verify that the correct image file is being used.
Error: Failed to install image - version mismatch between XOS and xmod=The selected partition does not have the same firmware version as the .xmod image file.
Error: Failed to install image - Package exists, please uninstall existing package first=Package exists, please uninstall existing package first
active partitions must be the same across the stack=All devices in the stack must be using the same active partition. Correct and repeat firmware download.
-----END FAILURE MAPPINGS-----
--
-----BEGIN SCRIPT "BootPROM Download"-----
download bootrom %TFTP_IP% %RELATIVE_TARGET_FILE_PATH% vr "%VR_VAR%"
@key y
@COMMANDDONE 30
exit
-----END SCRIPT-----
-----BEGIN SUCCESS "BootPROM Download"-----
Bootrom installed successfully
-----END SUCCESS-----
-----BEGIN FAILURE MAPPINGS "BootPROM Download"-----
-----END FAILURE MAPPINGS-----
--
-----BEGIN SCRIPT "Reset"-----
reboot
y
-----END SCRIPT-----
-----BEGIN SCRIPT "Timed Reset"-----
disable clipaging
reboot time %TIMED_RESET_ABSOLUTE_TIME%
y
show switch
exit
-----END SCRIPT-----
-----BEGIN SUCCESS "Timed Reset"-----
^Next Reboot:(?!.*None scheduled)
-----END SUCCESS-----
-----BEGIN FAILURE MAPPINGS "Timed Reset"-----
Error: Scheduled reboot time is in the past=Scheduled reboot time must be in the future.
-----END FAILURE MAPPINGS-----
--
-----BEGIN SCRIPT "Timed Reset Abort"-----
disable clipaging
reboot cancel
show switch
exit
-----END SCRIPT-----
-----BEGIN SUCCESS "Timed Reset Abort"-----
Next Reboot:\s*None scheduled
-----END SUCCESS-----
-----BEGIN USER-DEFINED VARIABLES -----
VR_VAR.Default=VR-Default
PUT_FILE_CMD.Default=tftp %TFTP_IP% -v "%VR_VAR%" -p -l %LOCAL_FILE_NAME% -r %REMOTE_FILE_NAME%
GET_FILE_CMD.Default=tftp %TFTP_IP% -v "%VR_VAR%" -g -l %LOCAL_FILE_NAME% -r %REMOTE_FILE_NAME%
RESTORE_PRIMARY_CMD.Default=tftp get %TFTP_IP% vr "%VR_VAR%" %RELATIVE_TARGET_FILE_PATH% primary.cfg force-overwrite
-----END USER-DEFINED VARIABLES -----

[Marco_Lorenz]

The most recent one. v6.3.x which I downloaded and installed today.

[Ronald_Dvorak]

Marco,

could you tell us the Netsight version that you use.

-Ron

[Ty_Izzet]

Marco,

I did have to close Inventory manager and reopen it for the menu to refresh. The script was also labeled with a .txt extension in the devicefiles folder.

DeviceFamilyDefTemplate.txt
new.txt
/usr/local/Extreme_Networks/NetSight/appdata/InventoryMgr/properties/devicefiles$

[Marco_Lorenz]

I tried it with .cfg and .txt. Restarted inventory manager and the whole server. No success....

[Marco_Lorenz]

Thanks for the Reply. Nice try, but i doesn't work for me. I still cannot see the script in the dropdownmenu.

Anyone else an idea?

Kind Reagrds

Marco