cancel
Showing results for 
Search instead for 
Did you mean: 

Port channel between x440g2 48 p and cisco cat 6500

Port channel between x440g2 48 p and cisco cat 6500

Lutha
New Contributor II
i have configured port channel on my cisco and extreme switch but when i connect the interfaces the port channel doesnt come up not sure what i am doing wrong here. please see configuration

CISCO CONFIG
------------------------------------------------------------------------------------------

interface Port-channel2
description 7th Floor Copper Trunk Uplinks
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-14,16-20,24-29,31-4094
switchport mode trunk
bandwidth 4096000
no ip address
logging event link-status
logging event spanning-tree status
logging event bundle-status
logging event trunk-status
load-interval 30
snmp ifindex persist
mls qos trust cos
spanning-tree portfast trunk
spanning-tree link-type point-to-point
end

interface range GigabitEthernet2/11 - 12
description 7th Floor Copper Uplink 1
switchport
switchport trunk allowed vlan 1-14,16-20,24-29,31-4094
switchport mode trunk
no ip address
logging event link-status
logging event spanning-tree status
logging event bundle-status
logging event trunk-status
load-interval 30
keepalive 30
mls qos trust cos
spanning-tree portfast trunk
spanning-tree link-type point-to-point
channel-protocol pagp
channel-group 2 mode desirable
end

EXOS CONFIG
-------------------------------------------------------------------------------------------------
enable sharing 1:2 grouping 1:2,3:48 algorithm address-based L2

sh sharing detail
Load Sharing Monitor
Config Current Agg Min Ld Share Dist Ld Share Agg Link Link Up
Master Master Control Active Algorithm Flags Group Mbr State Transitions
================================================================================
1:2 1:2 Static 1 L2 A 1:2 Y A 5
L2 3:48 - R 1
==============================================================================
12 REPLIES 12

Lutha
New Contributor II
HI Guys

I have tried below configuration and port channel still doesnt work
================================================================

interface Port-channel 3
description 7th Floor Copper Trunk Uplinks
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-14,16-20,24-29,31-4094
switchport mode trunk
bandwidth 4096000
no ip address
logging event link-status
logging event spanning-tree status
logging event bundle-status
logging event trunk-status
load-interval 30
snmp ifindex persist
mls qos trust cos
spanning-tree portfast trunk
spanning-tree link-type point-to-point
end

interface range GigabitEthernet3/7 - 8
description 7th Floor Copper Uplink 3
switchport
switchport trunk allowed vlan 1-14,16-20,24-29,31-4094
switchport mode trunk
no ip address
logging event link-status
logging event spanning-tree status
logging event bundle-status
logging event trunk-status
load-interval 30
keepalive 30
mls qos trust cos
spanning-tree link-type point-to-point
channel-group 3 mode active
end

on extreme side
enable sharing 1:2 grouping 1:2,3:48 algorithm address-based L2 lacp

m at my wits end now m not sure where i go wrong

Can a member kindly share their port channel configs between cisco device and extreme.

Thanks

Brian_Austin
Extreme Employee
Lutha,
please note if you need to configure the exos side for lacp as well as it looks like it is currently setup as a static lag

the following article should be able to help you achieve this:
https://gtacknowledge.extremenetworks.com/articles/How_To/how-to-configure-sharing-LAG-LACP-in-Summi...

Regards,

GONÇALO_NUNO_CO
New Contributor III
Hi,

Pagp is a Cisco proprietary protocol it is not support by any other vendor, you need to configure the Cisco with LACP.

Regards
GTM-P2G8KFN