Cant ping pc connected to switch

[asotorrios]

Hi,
im configuring a typology as follows:

pc60 - switch4(x440) - core(x460) - switch11(x440) - pc50

I can ping both x440 from the core and the core from them. I also can ping switch 4 from switch 11 but not the other way around.

I also can't ping from or to the pcs. Nor from the same switch they are connected, nor from other or the other pc.

I'm super new in this configurations so I'm sure I'm missing something important if i can't even ping from the pc directly connected to the switch.

PC is 132.53.64.60

Here is the switch4 config:

sh config
#
# Module devmgr configuration.
#
configure snmp sysContact "support@extremenetworks.com, +1 888 257 3000"
configure slot 1 module X440G2-24p-10G4
configure sys-recovery-level slot 1 reset
configure slot 2 module X440G2-24p-10G4
configure sys-recovery-level slot 2 reset
configure slot 3 module X440G2-24p-10G4
configure sys-recovery-level slot 3 reset

#
# Module vlan configuration.
#
configure vlan default delete ports all
configure vr VR-Default delete ports 1:1-28,2:1-28,3:1-28
configure vr VR-Default add ports 1:1-28,2:1-28,3:1-28
configure vlan default delete ports 1:1-28,2:1-28,3:1-28
create vlan "Control"
configure vlan Control description "Control"
configure vlan Control tag 101
enable sharing 1:24 grouping 1:24,2:24,3:24 algorithm address-based L2
configure vlan Control add ports 1:1,1:23-26,2:1-2,2:23,2:25-26,3:1-2,3:23,3:25-26 tagged
configure vlan Default add ports 1:1-28,2:1-23,2:25-28,3:1-23,3:25-28 tagged
configure vlan Default ipaddress 132.53.64.4 255.255.255.0
configure vlan Mgmt ipaddress 132.53.64.4 255.255.255.0

#
# Module mcmgr configuration.
#

#
# Module fdb configuration.
#

#
# Module rtmgr configuration.
#
configure iproute add default 132.53.64.254

#
# Module policy configuration.
#

#
# Module aaa configuration.
#
configure account admin encrypted

#
# Module acl configuration.
#




#
# Module bfd configuration.
#

#
# Module cfgmgr configuration.
#

#
# Module dosprotect configuration.
#

#
# Module dot1ag configuration.
#

#
# Module eaps configuration.
#

#
# Module edp configuration.
#

#
# Module elrp configuration.
#

#
# Module ems configuration.
#
#
# Module epm configuration.
#

#
# Module erps configuration.
#

#
# Module esrp configuration.
#

#
# Module ethoam configuration.
#

#
# Module etmon configuration.
#

#
# Module exsshd configuration.
#


#
# Module hal configuration.
#

#
# Module idMgr configuration.
#

#
# Module ipSecurity configuration.
#

#
# Module ipfix configuration.
#

#
# Module lldp configuration.
#

#
# Module mrp configuration.
#

#
# Module msdp configuration.
#

#
# Module netLogin configuration.
#

#
# Module netTools configuration.
#

#
# Module ntp configuration.
#
enable ntp
configure ntp server add xxxx

#
# Module poe configuration.
#

#
# Module rip configuration.
#

#
# Module ripng configuration.
#

#
# Module snmpMaster configuration.
#
#
# Module stp configuration.
#
configure stpd s0 priority 16384
enable stpd s0 auto-bind vlan Control
configure stpd s0 add vlan Default ports 1:1 dot1d
configure stpd s0 add vlan Default ports 1:2 dot1d
configure stpd s0 add vlan Default ports 1:3 dot1d
configure stpd s0 add vlan Default ports 1:4 dot1d
configure stpd s0 add vlan Default ports 1:5 dot1d
configure stpd s0 add vlan Default ports 1:6 dot1d
configure stpd s0 add vlan Default ports 1:7 dot1d
configure stpd s0 add vlan Default ports 1:8 dot1d
configure stpd s0 add vlan Default ports 1:9 dot1d
configure stpd s0 add vlan Default ports 1:10 dot1d
configure stpd s0 add vlan Default ports 1:11 dot1d
configure stpd s0 add vlan Default ports 1:12 dot1d
configure stpd s0 add vlan Default ports 1:13 dot1d
configure stpd s0 add vlan Default ports 1:14 dot1d
configure stpd s0 add vlan Default ports 1:15 dot1d
configure stpd s0 add vlan Default ports 1:16 dot1d
configure stpd s0 add vlan Default ports 1:17 dot1d
configure stpd s0 add vlan Default ports 1:18 dot1d
configure stpd s0 add vlan Default ports 1:19 dot1d
configure stpd s0 add vlan Default ports 1:20 dot1d
configure stpd s0 add vlan Default ports 1:21 dot1d
configure stpd s0 add vlan Default ports 1:22 dot1d
configure stpd s0 add vlan Default ports 1:23 dot1d
configure stpd s0 add vlan Default ports 1:25 dot1d
configure stpd s0 add vlan Default ports 1:26 dot1d
configure stpd s0 add vlan Default ports 1:27 dot1d
configure stpd s0 add vlan Default ports 1:28 dot1d
configure stpd s0 add vlan Default ports 2:1 dot1d
configure stpd s0 add vlan Default ports 2:2 dot1d
configure stpd s0 add vlan Default ports 2:3 dot1d
configure stpd s0 add vlan Default ports 2:4 dot1d
configure stpd s0 add vlan Default ports 2:5 dot1d
configure stpd s0 add vlan Default ports 2:6 dot1d
configure stpd s0 add vlan Default ports 2:7 dot1d
configure stpd s0 add vlan Default ports 2:8 dot1d
configure stpd s0 add vlan Default ports 2:9 dot1d
configure stpd s0 add vlan Default ports 2:10 dot1d
configure stpd s0 add vlan Default ports 2:11 dot1d
configure stpd s0 add vlan Default ports 2:12 dot1d
configure stpd s0 add vlan Default ports 2:13 dot1d
configure stpd s0 add vlan Default ports 2:14 dot1d
configure stpd s0 add vlan Default ports 2:15 dot1d
configure stpd s0 add vlan Default ports 2:16 dot1d
configure stpd s0 add vlan Default ports 2:17 dot1d
configure stpd s0 add vlan Default ports 2:18 dot1d
configure stpd s0 add vlan Default ports 2:19 dot1d
configure stpd s0 add vlan Default ports 2:20 dot1d
configure stpd s0 add vlan Default ports 2:21 dot1d
configure stpd s0 add vlan Default ports 2:22 dot1d
configure stpd s0 add vlan Default ports 2:23 dot1d
configure stpd s0 add vlan Default ports 2:25 dot1d
configure stpd s0 add vlan Default ports 2:26 dot1d
configure stpd s0 add vlan Default ports 2:27 dot1d
configure stpd s0 add vlan Default ports 2:28 dot1d
configure stpd s0 add vlan Default ports 3:1 dot1d
configure stpd s0 add vlan Default ports 3:2 dot1d
configure stpd s0 add vlan Default ports 3:3 dot1d
configure stpd s0 add vlan Default ports 3:4 dot1d
configure stpd s0 add vlan Default ports 3:5 dot1d
configure stpd s0 add vlan Default ports 3:6 dot1d
configure stpd s0 add vlan Default ports 3:7 dot1d
configure stpd s0 add vlan Default ports 3:8 dot1d
configure stpd s0 add vlan Default ports 3:9 dot1d
configure stpd s0 add vlan Default ports 3:10 dot1d
configure stpd s0 add vlan Default ports 3:11 dot1d
configure stpd s0 add vlan Default ports 3:12 dot1d
configure stpd s0 add vlan Default ports 3:13 dot1d
configure stpd s0 add vlan Default ports 3:14 dot1d
configure stpd s0 add vlan Default ports 3:15 dot1d
configure stpd s0 add vlan Default ports 3:16 dot1d
configure stpd s0 add vlan Default ports 3:17 dot1d
configure stpd s0 add vlan Default ports 3:18 dot1d
configure stpd s0 add vlan Default ports 3:19 dot1d
configure stpd s0 add vlan Default ports 3:20 dot1d
configure stpd s0 add vlan Default ports 3:21 dot1d
configure stpd s0 add vlan Default ports 3:22 dot1d
configure stpd s0 add vlan Default ports 3:23 dot1d
configure stpd s0 add vlan Default ports 3:25 dot1d
configure stpd s0 add vlan Default ports 3:26 dot1d
configure stpd s0 add vlan Default ports 3:27 dot1d
configure stpd s0 add vlan Default ports 3:28 dot1d
configure stpd s0 add vlan Default ports 1:24 dot1d

#
# Module synce configuration.
#

#
# Module techSupport configuration.
#

#
# Module telnetd configuration.
#

#
# Module tftpd configuration.
#

#
# Module thttpd configuration.
#

#
# Module twamp configuration.
#

#
# Module vmt configuration.
#

#
# Module vsm configuration.
#


Thanks

[asotorrios]

Thank you, both those solutions (and disabling windows firewall) made it work.

[Curtis_Brabham · Accepted solution]

What are your goals with the configuration? You have the Control and Default overlapping on ports, but as B-rad said, PC ports should be untagged unless you're configuring tagging on the NICs. That's an unnecessary step and will just add complexity to PC deployments. Not all desktop-level NICs have a tagging option, either.

Also run the following. I don't see that in the config.

code:

enable ipforwarding

[BradP]

Ports connected to PCs shouldn't be tagged unless the PC NIC is configured for that same tag ID. First try adding the port as untagged and see if it works.