How to config Radius Realm
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-22-2015 10:58 PM
Form Version 16.x show radius thate has Realm information
Realm :Any
from config radius command no include realm parameter.
Anyone konw how to set this parameter
Realm :Any
from config radius command no include realm parameter.
Anyone konw how to set this parameter
4 REPLIES 4
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎06-16-2017 03:03 AM
GOODNESS U SMART
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-23-2015 06:36 AM
"configure radius netlogin 1 server 1.1.1.2 client-ip 1.1.1.1 shared-secret 1234 vr "VR-Mgmt""
And if you add the netlogin key to the command before the index it will set the Realm to Netlogin
**Truncated output of "show radius**
Radius server : 1 Status is Active
host name :
IP address : 1.1.1.2
Server IP Port: 1812
Client address: 1.1.1.1 (VR-Mgmt)
Retries : 3 *
Timeout : 3 *
Realm : Netlogin
shared secret : #$9D35STS5EPKKghX+lPY=
Access Requests : 0 Access Accepts : 0
Access Rejects : 0 Access Challenges : 0
Access Retransmits: 0 Client timeouts : 0
Bad authenticators: 0 Unknown types : 0
Round Trip Time : 0
And if you add the netlogin key to the command before the index it will set the Realm to Netlogin
**Truncated output of "show radius**
Radius server : 1 Status is Active
host name :
IP address : 1.1.1.2
Server IP Port: 1812
Client address: 1.1.1.1 (VR-Mgmt)
Retries : 3 *
Timeout : 3 *
Realm : Netlogin
shared secret : #$9D35STS5EPKKghX+lPY=
Access Requests : 0 Access Accepts : 0
Access Rejects : 0 Access Challenges : 0
Access Retransmits: 0 Client timeouts : 0
Bad authenticators: 0 Unknown types : 0
Round Trip Time : 0
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-23-2015 06:25 AM
Hi Li,
I guess i misunderstood your question. may be here is the command you are looking for.
"configure radius 1 server 1.1.1.2 client-ip 1.1.1.1 shared-secret 1234 vr "VR-Mgmt""
Here in the above command i have only specified the index and not the realm and this server 1.1.1.2 is configured to Realm ANY
**Truncated output of "show radius**
Radius server : 1 Status is Active
host name :
IP address : 1.1.1.2
Server IP Port: 1812
Client address: 1.1.1.1 (VR-Mgmt)
Retries : 3 *
Timeout : 3 *
Realm : Any
shared secret : #$9D35STS5EPKKghX+lPY=
Access Requests : 0 Access Accepts : 0
Access Rejects : 0 Access Challenges : 0
Access Retransmits: 0 Client timeouts : 0
Bad authenticators: 0 Unknown types : 0
Round Trip Time : 0
I Hope this helps.
I guess i misunderstood your question. may be here is the command you are looking for.
"configure radius 1 server 1.1.1.2 client-ip 1.1.1.1 shared-secret 1234 vr "VR-Mgmt""
Here in the above command i have only specified the index and not the realm and this server 1.1.1.2 is configured to Realm ANY
**Truncated output of "show radius**
Radius server : 1 Status is Active
host name :
IP address : 1.1.1.2
Server IP Port: 1812
Client address: 1.1.1.1 (VR-Mgmt)
Retries : 3 *
Timeout : 3 *
Realm : Any
shared secret : #$9D35STS5EPKKghX+lPY=
Access Requests : 0 Access Accepts : 0
Access Rejects : 0 Access Challenges : 0
Access Retransmits: 0 Client timeouts : 0
Bad authenticators: 0 Unknown types : 0
Round Trip Time : 0
I Hope this helps.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-23-2015 05:54 AM
As per the command reference guide
"Switch management and network login use the same primary and secondary RADIUS servers for
authentication (only if the realm is not specified in the command).,"
The below command should configure the server for both Netlogin and mgmt-access
"configure radius primary server client-ip shared-secret 1234"
"Switch management and network login use the same primary and secondary RADIUS servers for
authentication (only if the realm is not specified in the command).,"
The below command should configure the server for both Netlogin and mgmt-access
"configure radius primary server
