Initial Configuration BD8810

[Mario_Cruz_Torr]

Hello Expert,

Im start configuring my first BD8810:

First I want to upgrade the node, but for that I configure a vlan with an IP Address but Im unable to ping the IP. [My computer has the 192.168.1.2/24]

This is my config:

enable port 1:1
create vlan "test"
configure vlan test tag 10
configure vlan test add ports 1:1 untagged
configure vlan test ipaddress 192.168.1.1 255.255.255.0
enable ipforwarding vlan test

There is something that I missing?? Maybe something new for the BlackDiamonds

Thanks

[Mario_Cruz_Torr]

Follow the info:
* BD-8810.165 # sh ports 1:1 information detail
Port: 1:1
Virtual-router: VR-Default
Type: UTP
Random Early drop: Unsupported
Admin state: Enabled with auto-speed sensing auto-duplex
Link State: Active, 1Gbps, full-duplex
Link Ups: 11 Last: Sun Sep 24 14:38:17 2017
Link Downs: 10 Last: Sun Sep 24 14:33:56 2017

VLAN cfg:
Name: test, Internal Tag = 100, MAC-limit = No-limit, Virtual router: VR-Default
STP cfg:

Protocol:
Name: test Protocol: ANY Match all protocols.
Trunking: Load sharing is not enabled.

EDP: Enabled

ELSM: Disabled
Ethernet OAM: Disabled
Learning: Enabled
Unicast Flooding: Enabled
Multicast Flooding: Enabled
Broadcast Flooding: Enabled
Jumbo: Disabled
Flow Control: Rx-Pause: Enabled Tx-Pause: Disabled
Priority Flow Control: Disabled
Reflective Relay: Disabled
Link up/down SNMP trap filter setting: Enabled
Egress Port Rate: No-limit
Broadcast Rate: No-limit
Multicast Rate: No-limit
Unknown Dest Mac Rate: No-limit
QoS Profile: None configured
Ingress Rate Shaping : Unsupported
Ingress IPTOS Examination: Disabled
Ingress 802.1p Examination: Enabled
Ingress 802.1p Inner Exam: Disabled
Ingress 802.1p Priority: 0
Egress IPTOS Replacement: Disabled
Egress 802.1p Replacement: Disabled
NetLogin: Disabled
NetLogin port mode: Port based VLANs
Smart redundancy: Enabled
Software redundant port: Disabled
IPFIX: Disabled Metering: Ingress, All Packets, All Traffic
IPv4 Flow Key Mask: SIP: 255.255.255.255 DIP: 255.255.255.255
IPv6 Flow Key Mask: SIP: ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff
DIP: ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff

auto-polarity: Enabled
Shared packet buffer: default
VMAN CEP egress filtering: Disabled
Isolation: Off
PTP Configured: Disabled
Time-Stamping Mode: None

Dynamic VLAN Uplink: Disabled
VM Tracking Dynamic VLANs: Disabled

------------------------------------------------------------------
* BD-8810.166 # show switch

SysName: BD-8810
SysLocation:
SysContact: support@extremenetworks.com, +1 888 257 3000
System MAC: 00:04:96:9C:C0:60
System Type: BD-8810

SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled

Current Time: Sun Sep 24 14:39:11 2017
Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
Boot Time: Thu Sep 21 15:24:17 2017
Boot Count: 3
Next Reboot: None scheduled
System UpTime: 2 days 23 hours 14 minutes 54 seconds

Slot: MSM-A * MSM-B
------------------------ ------------------------
Current State: MASTER BACKUP (In Sync)

Image Selected: primary primary
Image Booted: primary primary
Primary ver: 16.1.3.6 16.1.3.6
Secondary ver: 16.1.3.6 16.1.3.6

Config Selected: NONE NONE
Config Booted: Factory Default Factory Default

--------------------------------------------------------------------------------

Thanks so much for this help

Mario Cruz

[Ariyakudi_Srini]

Hi Mario Cruz,

Is ping from both the direction not functional or is the ping in any 1 direction not functional.

Also, please check the output of "show fdb port 1:1" to see if the MAC of the PC is learnt in the switch. And also check the output of "show iparp" to see if the IP address of the PC is learnt in the switch.

Let us also check if there are any errors occurring in the port and the command is as below,

- show port 1:1 rxerror
- show port 1:1 txerror

Thank You,
Muthuraman

[Mario_Cruz_Torr]

Hi,

Ping is not functional in both directions.

The MAC is learned via the fdb command but no via the iparp, And looking for the errors there is no such on the port.

Any idea.

Thanks

Mario

[Ariyakudi_Srini]

Hi Mario Cruz,

I see all the necessary configuration for the communication to happen between the PC (192.168.1.24/24) and the BD8810 (192.168.1.1/24).
I don't see a reason as to why the ping will not go through between the switch and the PC.

Is there any firewall that is enabled in the PC that could be taken down and checked?

What about the port LED status and please check the output of "show port 1:1" to see if the status of the port is "Enabled" and "Active".

Thank You,
Muthuraman

[Mario_Cruz_Torr]

Hello Muthuraman,

I remove the firewall on my laptop and the same issue.
The port is Active no issue with the cable.

There is something new for the BD to configure?? Like the modules? We just power on the equipments.

Thanks for the quick response.