Port cannot belong to VLAN and a VMAN at the same time.

[Drin]

Trying to configure QinQ solution between two extreme switches and im facing an issue when trying to make one of the ports untagged:

| Error: 8: Port cannot belong to VLAN and a VMAN at the same time.|

This port is not configured in any VLAN or VMAN as Untagged

This issue a get only in one SW, in the other one im able to configured the port as untagged.

The only difference between SW are the Image version running. But im not sure if that is the case?

[EtherMAN]

From the 12.1 concepts guide.... 450's are a bit different for that code rev

■ On Summit X150, X250e, X350, X450a, and X450e series switches, and on the BlackDiamond 8800a-series, c-series, and e-series modules, you can configure vMANs and VLANs on the same
module or on the same stand-alone switch regardless of the vMAN ethertype. However, vMANs
and VLANs cannot be configured on the same physical port, unless you change the vMAN
ethertype to 0x8100.
■ On Summit 250e, 450a, and 450e family switches and the BlackDiamond 8800 a-series, c-series,
and e-series modules, you can configure vMANs and VLANs on the same port as follows:
■ Tagged and untagged vMANs on the same port (vMAN ethertype = 0x8100)
■ Tagged vMANs and tagged VLANs on the same port (vMAN ethertype = 0x8100)
■ Tagged vMANs and untagged VLANs on the same port
NOTE

[Drin]

SW that im able to configure port UNTAGGED
show switch

System Type: X450a-48t

SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled

Current Time: Sat Mar 26 18:00:04 1921
Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
Boot Time: Sat Mar 6 08:49:23 1920
Boot Count: 8
Next Reboot: None scheduled
System UpTime: 385 days 9 hours 10 minutes 41 seconds

Current State: OPERATIONAL
Image Selected: primary
Image Booted: primary
Primary ver: 12.4.1.7
Secondary ver: 12.4.1.7

Config Selected: primary.cfg
Config Booted: primary.cfg

primary.cfg Created by ExtremeXOS version 12.4.1.7
212814 bytes saved on Sat Mar 26 15:09:46 1921

show version

Switch : 800163-00-05 0802G-80203 Rev 5.0 BootROM: 1.0.2.2 IMG: 12.4.1.7
XGM2-1 : N/A N/A Rev 0.0

Image : ExtremeXOS version 12.4.1.7 v1241b7 by release-manager
on Sat Mar 13 02:36:57 EST 2010
BootROM : 1.0.2.2

############################################

SW that im unable to configure port UNTAGGED

show switch

System Type: X450a-48t

SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled

Current Time: Thu Mar 3 22:36:57 2016
Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
Boot Time: Fri Aug 8 16:43:00 2014
Boot Count: 5
Next Reboot: None scheduled
System UpTime: 573 days 5 hours 53 minutes 57 seconds

Current State: OPERATIONAL
Image Selected: secondary
Image Booted: secondary
Primary ver: 12.4.1.7
Secondary ver: 12.1.2.17

Config Selected: primary.cfg
Config Booted: primary.cfg

primary.cfg Created by ExtremeXOS version 12.1.2.17
198565 bytes saved on Thu Mar 3 19:45:38 2016

show version

Switch : 800163-00-08 0938G-80032 Rev 8.0 BootROM: 1.0.3.5 IMG: 12.1.2.17
XGM2-1 :

Image : ExtremeXOS version 12.1.2.17 v1212b17-patch1-10 by release-manager
on Thu Jan 8 21:02:01 PST 2009
BootROM : 1.0.3.5

[EtherMAN]

are both switches 450's ?

[Drin]

Please see additional information from other SW when im able to add port as untagged

show ports 3 information detail
Port: 3(name):
Virtual-router: VR-Default
Type: UTP
Random Early drop: Unsupported
Admin state: Enabled with auto-speed sensing auto-duplex
Link State: Active, 1Gbps, full-duplex
Link Counter: Up 8 time(s)

VLAN cfg:
Name: VLAN_NAMES 802.1Q Tag = 236, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 237, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 238, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 241, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 325, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 347, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 205, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 600, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 11, MAC-limit = No-limit, Virtual router: VR-Default
Name: VLAN_NAMES 802.1Q Tag = 12, MAC-limit = No-limit, Virtual router: VR-Default
Name: VMAN_NAME Internal Tag = 324, MAC-limit = No-limit, Virtual router: VR-Default

STP cfg:

Protocol:
Name: VMAN_NAME Protocol: ANY Match all protocols.
Trunking: Load sharing is not enabled.
EDP: Enabled
ELSM: Disabled
Ethernet OAM: Disabled
Learning: Enabled
Unicast Flooding: Enabled
Multicast Flooding: Enabled
Broadcast Flooding: Enabled
Jumbo: Enabled, MTU= 9216
Flow Control: Rx-Pause: Enabled Tx-Pause: Disabled
Link up/down SNMP trap filter setting: Enabled
Egress Port Rate: No-limit
Broadcast Rate: No-limit
Multicast Rate: No-limit
Unknown Dest Mac Rate: No-limit
QoS Profile: None configured
Ingress Rate Shaping : Unsupported
Ingress IPTOS Examination: Disabled
Ingress 802.1p Examination: Enabled
Ingress 802.1p Inner Exam: Disabled
Egress IPTOS Replacement: Disabled
Egress 802.1p Replacement: Disabled
NetLogin: Disabled
NetLogin port mode: Port based VLANs
Smart redundancy: Enabled
Software redundant port: Disabled
auto-polarity: Enabled

############################

configure vman VMAN_NAME add ports 47 tagged
configure vman VMAN_NAME add ports 3 untagged

[Drin]

Hi Brandon,

I as explained in the beginning im able to do port untagged in the other SW and working perfectly.

But in this sw im unable to do it and the error you already have it in description