Stack Extreme X460-G2-24-t-10GE4 with VIM-2SS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-27-2019 02:02 AM
Hello Guys
I have two extreme switch X460-G2-24t-10GE4 with module Summit X460-G2 VIM-2SS.
When running stack command in both switch, both switch show me Master
Slot-1 Stack.3 # show stacking
Stack Topology is a Daisy-Chain
Active Topology is a Daisy-Chain
Node MAC Address Slot Stack State Role Flags
------------------ ---- ----------- ------- ---
*00:04:96?3d:XX 1 Active Master CA-
* - Indicates this node
Flags: (C) Candidate for this active topology, (A) Active Node
(O) node may be in Other active topology
In both switch run the following:
Firts Switch:
enable stacking node-address 00:04:96?3d:XX
conf stacking node-address 00:04:96?3d:XX slot-number 1
conf stacking node-address 00:04:96?3d:XX master-capability on
conf stacking node-address 00:04:96?3d:XX priority 70
conf stacking node-address mac-address 00:04:96?3d:XX
conf slot 1 module X460G2-24t-10G4
save
Second Switch
enable stacking node-address 00:04:96?3d:YY
conf stacking node-address 00:04:96?3d:80 slot-number 2
conf stacking node-address 00:04:96?3d:80 master-capability on
conf stacking node-address 00:04:96?3d:80 priority 60
conf stacking node-address mac-address 00:04:96?3d:YY
conf slot 1 module X460G2-24t-10G4
save
Is possible your help with the configuration of Stack?
Regards
Sebastian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-09-2020 02:08 PM
If I understand this article correctly, it should work:
Open a TAC case if possible.
/Fredrik
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-03-2020 03:36 PM
Hello
I configure module VIM-2ss in native mode with stack-ports all selection native but ever show me both Switch in Master Role.
Also running easy-setup and the problem persist.
Now when change to Alternative the stacking is available.
I think the module is not compatible because I test in other switch x460-G2 and have the same problem.
Any idea.
Regards
Sebastian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-28-2019 08:13 PM
Switch 1 has no config telling it which MAC switch 2 has and vice versa. If this is a new setup, use the easy setup command described here:
If you have an EXOS of 22.6 or later, it may have a new type of stacking method called ZTP stacking:
“Automation for Adding/Replacing Stack Nodes
A new automated process allows you to easily add or replace nodes in a stack. This automation performs the following tasks in a stack:
- Adds New Nodes—When new switches are attached to an existing stack, adds those switches to the stack without manual configuration.
- Incompatible ExtremeXOS Check—Checks for and resolves incompatible ExtremeXOS software versions of stack nodes.
- License Mismatch Check—Checks for and resolves software license mismatches between all master- capable nodes.
Supported Platforms
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X590, X620, X690, X870 series switches.
Limitations
- Except for the Summit X450-G2 and X460-G2 with VIM2-SS modules, all switches require that you configure stacking on the stacking ports manually (configure stackingsupport stack- port [stack-ports | all] selection [native {V80 | V160} | V320 |V400} | alternate]).
- License mismatches due to installing feature licenses cannot be automatically resolved. The node is left in the failed state.”
/Fredrik
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-28-2019 01:11 PM
Hi Sebastian,
have you properly connected both X460-G2 with a stacking cable? Can you provide the output of the command “show stacking config”?
Kind regards
Christian
