cancel
Showing results for 
Search instead for 
Did you mean: 

Used Summit X460-48P PoE switch w/ no console output, no mgmt IP, EDP on network interfaces, no PoE. Any help?

Used Summit X460-48P PoE switch w/ no console output, no mgmt IP, EDP on network interfaces, no PoE. Any help?

davidjohn
New Contributor

So I bought an Extreme Networks Summit X460-48P PoE switch for just under 20 bucks and I am struggling to get it to work. I contacted the agency I purchased it from and they said it worked fine, they just factory reset it. Here is what I've done:

  1. Checked for bulging capacitors-Everything that I saw looked good.

  2. Tried different console cables and computers, tried different console settings and tried holding down space bar at power on-No console output

  3. used Wireshark on the management interface to see if there is an IP address-saw nothing. But, I do see EDP packets on lan ports.

  4. Not contact Extreme support b/c I don't have a business email account, nor do I want to pay.

  5. Plugged in the CompactFlash into a computer and taken screenshots. (attached)

  6. Removed the compact flash card and powered it on and I get different lights blinking than normal.

  7. Noticed that eventually, the MGMT light will blink slowly after the boot process.

Any tips/help would be appreciated. Thank You!

8c227118ca974513aea0bc5390ec319b_844ad581-db55-4c59-832e-f786683251a5.png
8c227118ca974513aea0bc5390ec319b_873d8dea-a2e6-43cb-bcfc-6143bc2de195.png

 

1 ACCEPTED SOLUTION

Curtis_Brabham
New Contributor III

Are you sure you have the correct console cable?  It is a null modem connection.  I got tired of using adapters, so I purchased the following cable for older models with the DB9 RS232 port:

Amazon.com: DTECH 10 ft USB to RS232 DB9 Female Serial Port Adapter Cable with FTDI Chipset Supports...

 

For newer switches (and other manufacturers) that use the RJ45 style RS232 port, I use this cable:

Amazon.com: Asunflower 12 Ft FTDI USB to RJ45 for Cisco Router Console Cable - RS232: Computers & Ac...

 

Without a configuraiton on it, it’ll act as an unmanaged switch.  Have you tried plugging in two devices with static IPs (in the same range...so 10.1.1.1/24 and 10.1.1.2/24) to see if they can ping each other once the switch boots?  That would tell you that you at least have basic functionality.

PoE should also be working on a default config, as long as the device is PoE compliant.  There are some devices (I’m looking at you Ubiquiti) that use “passive PoE” and won’t power off of an actual PoE port.

 

View solution in original post

4 REPLIES 4

Curtis_Brabham
New Contributor III

Link for others:

(1) Used Summit X460-48P PoE switch w/ no console output, no mgmt IP, EDP on network interfaces, no ...

 

Also...I recently ran into an issue with an X460-48p that was purchased from eBay.  We ordered several, actually.  Anyway, one of them also had no console output and I know the cable i was using was the correct...I’ve used the same one for years.  We finally opened the switch (no warranty to worry about voiding) and discovered the ribbon cable for the DB9 port was disconnected from the pins on the circuit board.  We reconnected it and everything started working perfectly.

 

davidjohn
New Contributor

Yes it did end up being my console cable. You can find a more detailed account on the extreme sub redddit.

Curtis_Brabham
New Contributor III

Are you sure you have the correct console cable?  It is a null modem connection.  I got tired of using adapters, so I purchased the following cable for older models with the DB9 RS232 port:

Amazon.com: DTECH 10 ft USB to RS232 DB9 Female Serial Port Adapter Cable with FTDI Chipset Supports...

 

For newer switches (and other manufacturers) that use the RJ45 style RS232 port, I use this cable:

Amazon.com: Asunflower 12 Ft FTDI USB to RJ45 for Cisco Router Console Cable - RS232: Computers & Ac...

 

Without a configuraiton on it, it’ll act as an unmanaged switch.  Have you tried plugging in two devices with static IPs (in the same range...so 10.1.1.1/24 and 10.1.1.2/24) to see if they can ping each other once the switch boots?  That would tell you that you at least have basic functionality.

PoE should also be working on a default config, as long as the device is PoE compliant.  There are some devices (I’m looking at you Ubiquiti) that use “passive PoE” and won’t power off of an actual PoE port.

 

Drew_C
Valued Contributor III

Regarding console connectivity, does anything in this thread help?

GTM-P2G8KFN