Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎11-30-2018 02:58 PM
hallo,
i've twoo AP 7532 one as VC when i try to apply the option Adoption Mode on the VC ap and click on apply ,after refrsh the site i see that option is not mark, i remark the Adoption option and apply it again still the same ...?
please help with that
i've twoo AP 7532 one as VC when i try to apply the option Adoption Mode on the VC ap and click on apply ,after refrsh the site i see that option is not mark, i remark the Adoption option and apply it again still the same ...?
please help with that
Solved! Go to Solution.
1 ACCEPTED SOLUTION
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-06-2018 05:51 AM
I would try the configuration using CLI. Here are cli commands:
code:
>en
#self
Enter configuration commands, one per line. End with CNTL/Z.
#virtual-controller
#com wr
[ok]
#show context
5 REPLIES 5
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-07-2018 04:51 AM
Please see section "Wireless Mesh" in the WiNG 5.X Best Practices and Recommendations doc.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-06-2018 06:08 PM
ive try it again
and this is the resulat
Zolder(config-device-74-67-F7)#show context
ap7532 74-67-F7
use profile default-ap7532
use rf-domain default
hostname Zolder
location default
interface vlan1
description "WAN Interface"
ip address dhcp
ip dhcp client request options all
ip nat inside
no shutdown
ntp server nl.pool.ntp.org
virtual-controller
rf-domain-manager capable
ip dns-server-forward
logging on
logging console warnings
logging buffered warnings
ip nat inside source list default-7467F-nat precedence 1 interface vlan1 ......
so i think it's know okey write ....????
one more thing i'ev 3 AP 7532I with latste firmware and use them know with utp Cabel use both 2.4 and 5.i want to place one of the three in other place where i got no cable but there is no luck with Mesh cloud you help me with that please ...?
thanks
and this is the resulat
Zolder(config-device-74-67-F7)#show context
ap7532 74-67-F7
use profile default-ap7532
use rf-domain default
hostname Zolder
location default
interface vlan1
description "WAN Interface"
ip address dhcp
ip dhcp client request options all
ip nat inside
no shutdown
ntp server nl.pool.ntp.org
virtual-controller
rf-domain-manager capable
ip dns-server-forward
logging on
logging console warnings
logging buffered warnings
ip nat inside source list default-7467F-nat precedence 1 interface vlan1 ......
so i think it's know okey write ....????
one more thing i'ev 3 AP 7532I with latste firmware and use them know with utp Cabel use both 2.4 and 5.i want to place one of the three in other place where i got no cable but there is no luck with Mesh cloud you help me with that please ...?
thanks
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-06-2018 05:51 AM
I would try the configuration using CLI. Here are cli commands:
code:
>en
#self
Enter configuration commands, one per line. End with CNTL/Z.
#virtual-controller
#com wr
[ok]
#show context
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-06-2018 05:48 AM
