cancel
Showing results for 
Search instead for 
Did you mean: 

Why dont I get full EIRP from AP?

Why dont I get full EIRP from AP?

Paul_Holmgren
New Contributor
I try to do a test with creating a 5GHz link outdoor.

The link works but to know the maximum distance I can do with this AP/antenna combination I want to get the AP to use the maximum allowed EIRP.

But I only get half (500mW = 27dBm) instead of 30dBm.

this is my setting and status of radio.

ap6562-690AB4#sh wireless regulatory device-type ap6562 se
----------------------------------------------------------------------------------------------------
# Channel Set Power(mW) Power (dBm) Placement DFS CAC(mins) TPC
----------------------------------------------------------------------------------------------------
1 1-13 100 20 Indoor/Outdoor NA NA NA
2 36-48 200 23 Indoor Not Required 0 Not Required
3 52-64 100 20 Indoor Required 1 Not Required
4 52-64 200 23 Indoor Required 1 Required
5 100-116 500 27 Indoor/Outdoor Required 1 Not Required
6 100-116 1000 30 Indoor/Outdoor Required 1 Required
7 120-128 500 27 Indoor/Outdoor Required 10 Not Required
8 120-128 1000 30 Indoor/Outdoor Required 10 Required
9 132-140 500 27 Indoor/Outdoor Required 1 Not Required
10 132-140 1000 30 Indoor/Outdoor Required 1 Required
----------------------------------------------------------------------------------------------------
ap6562-690AB4#
Radio: 84-24-8D-69-0A-B4:R2, alias ap6562-690AB4:R2
STATE : On
PHY INFO : Bssid: 84-24-8D-69-0E-20 RF-Mode: 5GHz-wlan
ACCESS POINT : Name: ap6562-690AB4 Location: Test Placement: Outdoor
CHANNEL : Current: 100 Configured: 100 Width: 20MHz
TRANSMIT POWER : 17 dBm
ANTENNA USAGE : 2x2
MAXIMUM DATA RATES : Phy: 144 Mbps User: 108 Mbps
PHY SETTINGS : Short Preamble: N Dual Channel: N Spectrum Mgmt: Y
RATE SELECTION : Standard
ANTENNA DOWNTILT : Not-Supported
RADIO SHARE MODE : Off
TRANSMIT BEAMFORMING : -
MU-MIMO : Not-Supported
SCAN_AHEAD CHANNEL : -
ERP COEXISTENCE : ERP Protection: N Non-ERP detected: N Non-ERP associated: N
HT COEXISTENCE : HT Protection: no-protection, Non-HT detected: N
Current Channel Width: 20Mhz, reason: per configuration
Num of Mcast Streams : 0 (max:25)
Multicast streams :
# MP Mcast Streams : 0
WLAN MAP :
BSS-1 : Test* (*=primary)
Shutdown WLANs :
MESHPOINT map :
BSS MAP :
BSS-1 : basic-rates = 6 12 24
: supported-rates= 6 9 12 18 24 36 48 54 mcs-1s mcs-2s
Last error :

ap6562 84-24-8D-69-0A-B4
use profile default-ap6562
use rf-domain Test
hostname ap6562-690AB4
interface radio2
channel 100
power 30
wlan Test bss 1 primary
antenna-gain 10.0
no dynamic-chain-selection
ap6562-690AB4(config-device-84-24-8D-69-0A-B4)#end

AP is powered by a 802.3at capable switch.

If I fool the AP that I have a 7dBi antenna instead it amplifies the IR to 20dBm so its something I cant see.

Kind regards

Paul

13 REPLIES 13

Timo1
New Contributor II
Really? Datasheet says:

Maximum Available Transmit Power:

2.4GHz: 21dBm Per Chain

5GHz: 20dBm Per Chain

You already do more power as the AP can ;D



Hi,

Strange that that a Outdoor AP with built in heat does NOT support TPC.

Can you give me some documentation that supports that?

Timo1
New Contributor II
Hi,

you need to configure the radio for outdoor. Max. 30dBm is EIRP or TX power in your country?

30dBm EIRP with 2x2 radio, TX power is 27dBm, based on the MIMO. For 1x1 you can do 30dBm.

Timo1
New Contributor II
For this case, open a GTAC. I had some problems last year with AP6522. Mostly the same, but if I can remember with 14dBm max TX power.

After some mails looks like, radio problem. I think AP6522 and AP6562 use the same radio.

I have now lowered the radio to 1x1.

and that does not change any behaviour on the AP.

CHANNEL : Current: 100 Configured: 100 Width: 20MHz
TRANSMIT POWER : 17 dBm
ANTENNA USAGE : 1x1

transmit power is what AP is selecting it self.

I have configured it for 30dBm EIRP.

GTM-P2G8KFN