Showing results for 
Search instead for 
Did you mean: 

MSTP in a rapidly changing environment

MSTP in a rapidly changing environment

New Contributor II
I'm having a hard time integrating MSTP in my environment.
Basically it's a rapidly changing environment where projects change on a weekly, sometimes even daily basis.
This means that adding VLANs and creating new networks and firewall policies is a very frequent task.

The topology consists of a pair of core switches (MLAG peers) and lots of edge switches (20+). All of those belong to the same MSTP region.

What happens is that often I have to add another VLAN/network for a particular area (covered by a particular edge switch) and since I want to have it protected by STP i end up with a very time consuming task.
Problem is, when I create another VLAN I have to make MSTP digest consistent throughout my whole topology.
That means I have to go through all of core and ALL of my edge switches (20-30 of them) and create the VLAN, auto-bind it to a MSTI and finally even add it to the uplink.
Basically it's such an overhead I'm almost thinking of binding only permanenly existing VLANs (e.g. infrastructure, sales...) and leave the project VLANs outside of STP completely.

Creating a script to automate the config at least on the edge switches seems very dangerous...

I hate to say this but something like this is a breeze on cisco.
There you can manage and propagate VLANs with VTP (yes i know of the shortcomings...); MSTP can be configured in advance identically everywhere since VLANs don't have to _exist_ in order to be defined in MSTI config.

I desperately need some advice or suggestion how to reduce the overhead this imposes...

To sum it up,
Problem 1 - is there really no way to make MSTP config consistent everywhere before VLANs are even created on the switch? E.g. configure mstp to bind vlans 1-999 to MSTI before all of those VLANs even exist - just so that the digest matches everywhere.

Problem 2 - is there really no way to simplify VLAN propagation? MVRP comes really close but it's meant only for AVB. Since it's impossible to manually adding ports to dynamically created VLAN it's useless in this scenario.

If those problems aren't solved, how do you guys cope?

Thanks in advance,



Extreme Employee
If we create a version of ezspantree that works with 16.1, would that solve the problem? It would function the same way as

Valued Contributor
Do you need MSTP to the edge, or could you just have it at the core and then have STP at the edge?

New Contributor II
Hypothetically, let's say I were to have all extreme hw and decide on MLAG and ELRP.
I'm going off topic here, so If needed i'll open another discussion.

Since access port VLAN membership changes frequently, I guess ELRP has to be configured for all VLANs. Having a dummy vlan for ELRP doesn't seem like a solution since ELRP frames have to be untagged when leaving the access port? Tagged ELRP frames would be dropped by customer equipment and loops wouldn't be detected.

First, what about CPU footprint on ELRP for few hundred VLANs?

Second, is it planned to implement the vlan range configuration for elrp?
Even with 16.1.3 sw it's not possible to simply run "configure elrp-client periodic vlan <1-4095> .... ".
I was really overjoyed when I upgraded to 16.1+ and discovered this "enhancement".

On a side note..Interesting how nobody asked when I mentioned MLAG and STP in the same sentence...
I just read in the documentation that STP and MLAG ports don't go together.
Basically i'd be stuck with multiple (M)STP isolated segments (on each edge sw).

New Contributor
Even with Edge-safeguard enabled? Below is a sample config of what I've used.

create vlan "STPVlan"configure vlan STPVlan tag 1111
configure vlan STPVlan add ports all tagged

configure mstp region STPVlan
configure stpd s0 delete vlan default ports all
disable stpd s0 auto-bind vlan default
configure stpd s0 mode mstp cist
create stpd STPVlan_stm
configure stpd STPVlan_stm mode mstp msti 1

configure stpd STPVlan_stm add vlan STPVlan ports all dot1d

configure stpd s0 ports mode dot1d 1:1-52,2:1-24
configure stpd s0 ports cost auto 1:1-52,2:1-24
configure stpd s0 ports link-type edge 1:1-48,2:1-24
configure stpd s0 ports edge-safeguard enable 1:1-48,2:1-24 recovery-timeout 60
configure stpd s0 ports bpdu-restrict enable 1:1-48,2:1-24 recovery-timeout 60

enable stpd s0 ports all

configure stpd STPVlan_stm ports mode dot1d 1:1-52,2:1-24
configure stpd STPVlan_stm ports cost auto 1:1-52,2:1-24

configure stpd STPVlan_stm ports edge-safeguard enable 1:1-48,2:1-24 recovery-timeout 60
configure stpd STPVlan_stm ports bpdu-restrict enable 1:1-48,2:1-24 recovery-timeout 60

enable stpd STPVlan_stm ports all
enable stpd s0
enable stpd STPVlan_stm