Profile

StephanH

Contact Details

My Content

1 to 20 of 50+ total
Posted By StephanH Oct 15, 2021 2:14 PM
Found In Egroup: ExtremeControl
\ view thread
Hello Ian, try an snmpwalk from XMC and NAC directly with your creds to be sure nothing is in between XMC/NAC and the switch. You start snmpwalk on XMC/NAC cli. Check if you are using the correct profile for you device in XMC. In addition check Alarm&Events->Events on XMC after you did an rediscover ...
Posted By StephanH Oct 15, 2021 2:05 PM
Found In Egroup: Firmware
\ view thread
Hello Ed, yes you can update the AP via GUI and configure the AP via CLI is impractical and that is not what the CLI is for. If you don't want to connect your AP to the cloud, the AP121 is not right for you. There are many APs on the market that work standalone (also from Extreme), which is certainly ...
Posted By StephanH Oct 15, 2021 2:58 AM
Found In Egroup: Firmware
\ view thread
Hello Ed, the AP121 is a cloud driven AP. The hole management and for example the softwareupdate is done via a cloud managment. You can create an account here: https://extremecloudiq.com/entry After first login you can choose a free account (=XIQ connect) with a smaller featureset. ------------------------------ ...
Posted By StephanH Oct 14, 2021 5:11 PM
Found In Egroup: Extreme Campus Controller
\ view thread
Hello Claudio, did it work? ------------------------------ Regards Stephan ------------------------------
Posted By StephanH Oct 14, 2021 5:06 PM
Found In Egroup: Documentation
\ view thread
Hello Tom, the APs are cloud APs, so first the question, do you have a cloud account and set up the APs there accordingly? Only then can the APs work. You should do that first. Here is a link that describes the LEDs. But as written, first connect to the cloud and then check the status of the LEDs. ...
Posted By StephanH Oct 14, 2021 10:57 AM
Found In Egroup: ExtremeSwitching (EXOS)
\ view thread
Hello @Stefan K., hello @Frank, I share your opinion. ​I have also switched off all notifications. One message for a new thread is enough, not for every post. Finally, thanks to Sam's adjustments to the new "Recent posts" menu, I can work in such a way that I look at the new threats a few times ...
Posted By StephanH Oct 4, 2021 1:20 PM
Found In Egroup: Extreme Campus Controller
\ view thread
Ok, if you want to switch the SSIDs only for single APs then you can do it in the following way: You can apparently switch the SSID on and off per radio. I.e. you define all required SSIDs in the profile and then switch the SSIDs that are currently required on the radio as needed. Take a ...
Posted By StephanH Oct 4, 2021 12:54 PM
Found In Egroup: Extreme Campus Controller
\ view thread
If the SSIDs are the same for all APs that belong to a profile. You can make your changes directly to the profile. The access is done via the "ProfileManager" and the "ServiceManager". Where the so-called serviceIds are relevant for the profile. It is best to first look at the profiles with: "m ...
Posted By StephanH Oct 4, 2021 12:27 PM
Found In Egroup: Extreme Campus Controller
\ view thread
Hello, from the API guide: services Array of strings A list of the names of the services this AP is providing. They could be obtained by looking up its site and getting them from there but it is likely that it will be more efficient to include references to the services directly. This attribute ...
Posted By StephanH Oct 4, 2021 12:11 PM
Found In Egroup: Extreme Campus Controller
\ view thread
Hello Claudio, I am aware that you are using the API. But you have to find the switch that sets the hook in my image either via the API or you have to set the hook once manually, otherwise your settings will be overwritten by the profile as written by me. How should the AP know that he may no longer ...
Posted By StephanH Oct 4, 2021 11:50 AM
Found In Egroup: Extreme Campus Controller
\ view thread
Hello Claudio, The SSIDs are configured via the device group and the associated profile for the AP. I suspect you can write your settings (hence status 200), but the data will be overwritten by the configuration in the DeviceGroup/Profile. Try to set the checkbox in the “Advanced Setting” ...
Posted By StephanH Sep 3, 2021 6:18 AM
Found In Library: ExtremeSwitching (Other)
Posted By StephanH Jul 15, 2021 12:15 PM
Found In Egroup: ExtremeControl
\ view thread
Hi, I think the API is the best way. But for the sake of completeness you could of course also use the "Age End-Systems Older Than" and delete the client from groups after 14 days (but not add it to a group as you wish). (The settings can be found under Administration->Options->Access Control->Data ...
Posted By StephanH Jun 24, 2021 3:53 PM
Found In Egroup: Vulnerability Notices
\ view thread
Hello, the ExtremeCloud (=https://ezcloudx.com/) is missing on the KB, too. I know the ExtremeCloud is EoS but still under contract.
Posted By StephanH May 31, 2021 11:06 AM
Found In Egroup: General Network Management
\ view thread
Hello Sacha, the best way to integrate a CMDB into XMC is the NBI-API of the XMC. Among other ways,you can call the API directly from a remote system (e. g. your CMDB) or you can call the API directly from XMC and catch the data from the XMC (if you CMDB has an API, too). Here is a manual for the ...
Posted By StephanH Apr 20, 2021 7:41 AM
Found In Egroup: Scripting
\ view thread
Hello, here some basic info to start with python on EXOS: https://extremeportal.force.com/ExtrArticleDetail?an=000079734
Posted By StephanH Mar 17, 2021 7:15 PM
Found In Egroup: ExtremeSwitching (EXOS)
\ view thread
Hello, If you use disable sharing 1:42 the port config get lost in addition if the switch on the other sites is running you can create a loop in some situations. Therefore disable ALL ports in the sharing first. The better way is to remove single ports with configure sharing 1:42 delete port ...
Posted By StephanH Feb 10, 2021 8:08 PM
Found In Egroup: ExtremeCloud IQ- Site Engine & Extreme Management Center
\ view thread
Hello Byron, you can’t run the scripts from command line. The XMC python scripts are interpreted with jython enriched with the emc_vars, emc_cli … and compiled and run in Java.
Posted By StephanH Feb 4, 2021 8:06 PM
Found In Egroup: ExtremeCloud IQ- Site Engine & Extreme Management Center
\ view thread
Hello Byron, you can’t select individual months. But if you use python or TCL you can run one single script and check inside of you script the current month. Depending of the month you can run different functions every function with the content of you script1 - 4.
Posted By StephanH Nov 18, 2020 7:24 PM
Found In Egroup: ExtremeCloud IQ
\ view thread
Hello, I understand you perfectly. Basically I also feel like you. However, with limited resources you have to consider what to do first and what to do afterwards or not at all. In a business this means that a decisive factor is the money you can earn more with a feature. I don't like ...