No neighbor showing

[sanscorp]

Usage: Home use, 1 AP on every floor (concrete), 3 AP's in total.

DFS disabled

Default VLAN1

The hive is binded to Eth0, Wifi0.1 and Wifi1.1

I Tried the default device and radio template and a clone of both configured to always change channels when needed and always do background scans.

Problem:

3 AP's (AP121) all in the same hive (default VHM-MTUIWRLD) and none of the AP's lists a neighbor.

Show hive shows:

hive0        1       2346    2346    None
VHM-MTUIWRLD 1       2346    2346    VHM-MTUIWRLD

(Hive0 is not assigned to any interface)

ACSP neighbor list shows:

wifi1(6) ACSP neighbor list:
Bssid               Mode     Ssid/Hive           Chan  Rssi(dBm)  Aerohive AP  CU CRC STA Channel-width
*******      Backhaul VHM-MTUIWRLD        36    -83         yes          0  0   0   20
*******      Backhaul VHM-MTUIWRLD        36    -79         yes          0  0   0   20
*******      Access   SANSSID             40    -79         yes          0  0   0   20
*******      Access                       40    -81         yes          0  0   0   20

*******      Access   SANSSID             1     -69         yes          22 0   0   20
*******      Access   SANSSID             6     -76         yes          30 0   0   20

AP1#show hive VHM-MTUIWRLD neighbor
Chan=channel number; Pow=Power in dBm;
A-Mode=Authentication mode; Cipher=Encryption mode;
Conn-Time=Connected time; Hstate=Hive State;

Mac Addr       Chan Tx Rate Rx Rate Pow(SNR)     A-Mode   Cipher Conn-Time   Hstate Phymode Chan-width Hive
-------------- ---- ------- ------- -------- ---------- -------- --------- -------- ------- ---------- ----
 

show int wifi1 shows:

BGSCAN allow=enabled; BGSCAN during voice=disabled; BGSCAN interval=10 minutes;
BGSCAN CTS-to-Self=enabled; BGSCAN with client=enabled; BGSCAN with PS client=disabled;
Number of BGSCAN=0; Number of BGSCAN requested=5; Number of BGSCAN missed=5;

(other AP's did do a background scan, the config is the same on all devices.

Show config running shows:

security mac-filter VHM-MTUIWRLD default permit
security mac-filter SANSSID default permit
radio profile "Copy of radio_ng_ng0"
radio profile "Copy of radio_ng_ng0" phymode 11ng
radio profile "Copy of radio_ng_ng0" acsp interference-switch enable
radio profile "Copy of radio_ng_ng0" acsp interference-switch iu-threshold 35
radio profile "Copy of radio_ng_ng0" acsp interference-switch crc-err-threshold 35
no radio profile "Copy of radio_ng_ng0" backhaul failover
radio profile "Copy of radio_ng_ng0" interference-map enable
radio profile "Copy of radio_ng_ng0" short-guard-interval
radio profile "Copy of radio_ng_ng0" benchmark phymode 11b rate 11 success 60 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11b rate 5.5 success 70 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11g rate 36 success 70 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11g rate 24 success 80 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11a rate 36 success 70 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11a rate 24 success 80 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11n rate mcs4/2 success 80 usage 50
radio profile "Copy of radio_ng_ng0" benchmark phymode 11n rate 54 success 70 usage 50
radio profile sanssid_radio_ng_na0
radio profile sanssid_radio_ng_na0 phymode 11na
radio profile sanssid_radio_ng_na0 acsp interference-switch enable
radio profile sanssid_radio_ng_na0 acsp interference-switch iu-threshold 35
radio profile sanssid_radio_ng_na0 acsp interference-switch crc-err-threshold 35
radio profile sanssid_radio_ng_na0 interference-map enable
radio profile sanssid_radio_ng_na0 interference-map cu-threshold 35
radio profile sanssid_radio_ng_na0 interference-map crc-err-threshold 35
radio profile sanssid_radio_ng_na0 short-guard-interval
radio profile sanssid_radio_ng_na0 benchmark phymode 11b rate 11 success 60 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11b rate 5.5 success 70 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11g rate 36 success 70 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11g rate 24 success 80 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11a rate 36 success 70 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11a rate 24 success 80 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11n rate mcs4/2 success 80 usage 50
radio profile sanssid_radio_ng_na0 benchmark phymode 11n rate 54 success 70 usage 50
security-object SANSSID
security-object SANSSID security protocol-suite wpa-auto-psk ascii-key ***
client-monitor policy default_Policy problem-type association trigger-times 3 report-interval 3600
client-monitor policy default_Policy problem-type authentication trigger-times 3 report-interval 3600
client-monitor policy default_Policy problem-type networking trigger-times 3 report-interval 3600
ssid SANSSID
ssid SANSSID security-object SANSSID
ssid SANSSID security mac-filter SANSSID
ssid SANSSID multicast conversion-to-unicast auto
ssid SANSSID client-monitor-policy default_Policy
hive VHM-MTUIWRLD
hive VHM-MTUIWRLD security mac-filter VHM-MTUIWRLD
hive VHM-MTUIWRLD password ***
interface eth0 native-vlan 1
interface wifi0 radio profile "Copy of radio_ng_ng0"
interface wifi0 radio tx-power-control auto
interface wifi1 radio profile sanssid_radio_ng_na0
interface wifi1 mode access
interface mgt0 hive VHM-MTUIWRLD
interface wifi0 ssid SANSSID
interface wifi1 ssid SANSSID
kddr enable
lldp
hostname AP1
admin root-admin admin password ***
dns server-ip 192.168.0.1
dns domain-name local.domain
ntp server 0.nl.pool.ntp.org
ntp server 1.nl.pool.ntp.org second
ntp server 2.nl.pool.ntp.org third
ntp server 3.nl.pool.ntp.org fourth
ntp interval 60
clock time-zone 1
clock time-zone daylight-saving-time 03-28 01:59:59 10-31 02:59:59
snmp trap-info over-snmp
snmp trap-host v3 admin sanscorp auth md5 password *** encryption des password ***
snmp trap-host v3 192.168.0.1 admin sanscorp
config rollback enable
device-location "1e Etage"
snmp location "1e Etage"
snmp contact sander
snmp reader version v3 admin sanscorp auth md5 password *** encryption des password ***
capwap client server name fra-cws-0.extremecloudiq.com
capwap client server backup name fra-cwm.extremecloudiq.com
capwap client dtls hm-defined-passphrase *** key-id 1
capwap client vhm-name VHM-MTUIWRLD
no capwap client dtls negotiation enable
application reporting auto
application reporting upload

window 15 admin VHM-MTUIWRLD password *** basic
AP1#show hive VHM-MTUIWRLD
RTS=Request to send;
 

Roaming cache shows:

Roaming for this AP:     enabled
Maximum Caching Time:    3600 seconds
Caching update interval: 60 seconds
Caching update times:    60
Roaming hops:            1
Broadcast way:           access backhaul

Roaming cache furthermore shows a few clients with a few hops.

What can I try to fix this?

[jauesaia]

Hi, I have dual-band APs (125 & 105) running in air monitor mode on the 2.4 radios and ap mode on the 5.0 radios. When invoking "show ap arm neighbors ip-addr <ap ip address>", I am seeing only the neighbors from the 5.0 radio. Shouldn't I be seeing neighbors on the 2.4 band as well? Though ome controllers are running versions 3.4.2.5 of AOS, sims 3 lifetime rewards cheat while others are running 6.1.2.6, the result is still the same for the 2.4 AM access points-neighbors on 5.0, and nothing on 2.4. Thanks in advance,

[sanscorp]

I also cannot set the country code to one AP and thus change to the use of 4 channels and the use of channel 13.