cancel
Showing results for 
Search instead for 
Did you mean: 

7100 series LACP ports not dormant after connecting to server NIC team

7100 series LACP ports not dormant after connecting to server NIC team

Ken_Applebaum
New Contributor III
Hi, We are trying to configure a lag on a 7100 series switch. We have good experience with creating lags between switches, and ESXi hosts. However, this is the first time we have done this using Microsoft 2012 R2 NIC teaming. On the server, I created a 2 port team, using two 10GB ports on the server. The Teaming mode is LACP, and the Load balancing mode is Dynamic. Configured the lag on the 7100 series switch with the following commands: set lacp aadminkey lag.0.9 265 set port lacp port tg.1.3 aadminkey 265 set port lacp port tg.2.3 aadminkey 265 set port lacp port tg.1.3 enable set port lacp port tg.2.3 enable set port alias lag.0.9 “naz-as-60 Veeam tape server (2x10GB)” set port alias tg.1.3 “LAG9 naz-as-62 Veeam tape server” set port alias tg.2.3 “LAG9 naz-as-62 Veeam tape server” set port vlan tg.1-2.3 1063 mod set port vlan lag.09 1063 mod We first attempted this last week, but the individual ports did not go dormant, yet the lag was active when they were connected, so we backed out, concerned about a loop forming. When comparing the new lags (lag.0.9) config against other working lags on the switch, we saw that there were differences. The following was configured on lag.0.9, from an earlier lag that was configured in the past: set port lacp port tg.1.3 padminstate lacpagg set port lacp port tg.2.3 padminstate lacpagg So we figured that we could run the following to change this: clear port lacp port tg.1-2.3 padminstate all clear port lacp port tg.1-2.3 aadminstate all We then physically connected the server ports to the switch again, but as before, the lag member ports were still active. Then we saw another difference between this lag, and other working ones, these lag ports had a padminkey value set: set port lacp port tg.1.3 padminkey 149 set port lacp port tg.2.3 padminkey 149 So we did the following: clear port lacp port tg.1.3 padminkey clear port lacp port tg.2.3 padminkey We again physically connected the server to the switch, and we think a loop occurred. Below is the current output of show lacp, and show port lacp port: PH-DC-RB2_7100-2(su)->show lacp lag.0.9 Global Link Aggregation state: enabled Single Port LAGs: enabled Aggregator: lag.0.9 Actor Partner System Identifier: 20:b3:99:92:c1:c6 84:2b:2b:58:02:b8 System Priority: 32768 0 Admin Key: 265 Oper Key: 265 0 Attached Ports: None. Standby Ports: None. PH-DC-RB2_7100-2(su)->show port lacp port tg.1-2.3 status detail Global Link Aggregation state : enabled Port Instance: tg.1.3 Port enable state: Enabled ActorPort: 259 PartnerAdminPort: 259 ActorSystemPriority: 32768 PartnerOperPort: 259 ActorPortPriority: 32768 PartnerAdminSystemPriority: 32768 ActorAdminKey: 265 PartnerOperSystemPriority: 32768 ActorOperKey: 265 PartnerAdminPortPriority: 32768 ActorAdminState: -----GlA PartnerOperPortPriority: 32768 ActorOperState: -F----lA PartnerAdminKey: 259 ActorSystemID: 20-b3-99-92-c1-c6 PartnerOperKey: 259 SelectedAggID: none PartnerAdminState: --DCS-lp AttachedAggID: none PartnerOperState: --DC--lp MuxState: Detached PartnerAdminSystemID: 00-00-00-00-00-00 DebugRxState: port Disabled PartnerOperSystemID: 00-00-00-00-00-00 portStandbyReason: none Port Instance: tg.2.3 Port enable state: Enabled ActorPort: 451 PartnerAdminPort: 451 ActorSystemPriority: 32768 PartnerOperPort: 451 ActorPortPriority: 32768 PartnerAdminSystemPriority: 32768 ActorAdminKey: 265 PartnerOperSystemPriority: 32768 ActorOperKey: 265 PartnerAdminPortPriority: 32768 ActorAdminState: -----GlA PartnerOperPortPriority: 32768 ActorOperState: -F----lA PartnerAdminKey: 451 ActorSystemID: 20-b3-99-92-c1-c6 PartnerOperKey: 451 SelectedAggID: none PartnerAdminState: --DCS-lp AttachedAggID: none PartnerOperState: --DC--lp MuxState: Detached PartnerAdminSystemID: 00-00-00-00-00-00 DebugRxState: port Disabled PartnerOperSystemID: 00-00-00-00-00-00 portStandbyReason: none Here is the VLAN config: set port vlan tg.1.3 1063 set port vlan tg.2.3 1063 set port vlan lag.0.9 1063 set vlan egress 1063 lag.0.8-9;tg.1.3,19-20;tg.2.3,19-20 untagged Any suggestions at to what we may be doing wrong would be greatly appreciated. Thanks, Ken
10 REPLIES 10

Erik_Auerswald
Contributor II
Hi Ken,

your output shows "Attached Ports: None." for lag.0.9. Thus the LAG is not active, but the physical ports are used, if they have link and are enabled.

I would expect "show port status tg.1-2.3;lag.0.9" to display the ten gig ports as up, but the LAG as oper down.

If both ten gig ports are forwarding and the remote side is switching between them, a loop occurs. An ESXi host does not switch between vSwitch uplink ports, a Linux bridge does, Open vSwitch should not, I have no idea what Hyper-V does or is supposed to do in this situation. The output of "show spantree stats active" might give an idea what is going on, as might "show port egress tg.1-2.3;lag.0.9".

You can use "show port lacp port tg.1-2.3 counter" to check if LACP PDUs are received on the ports. Those counters should be slowly increasing. If they are increasing quickly (once per second), the remote side uses fast timers, and you would need to configure those on the Extreme switch as well. If the counters are not increasing, LACP is probably not active on the Hyper-V host uplinks.

Thanks,
Erik

Thanks Eric, Right now, the server is not connected to the switch. The server is not an ESX host. It is a MS 2012 R2 that will serve as a backup repository and tape server, and this is what makes it new to us. Thanks for the commands to get some visibility into the lag activity, this will be helpful when we attempt this again. - ken

Jason_Parker
Contributor
Here is what you need Configuring a Static LAG Identify the logical LAG ports (aggregator) you wish to Utilize (ex. lag.0.9) Identify the underlying physical ports that will comprise the LAG(ex: tg.1-2.3) Configure the aggregator and ports to use all the same aadminkey which is unique from the aadminkey used by other LAG's and ports Cli command format: set LACP static Example: set LACP static lag.0.9 tg.1-2.3 Note1. The portion is the virtual command will appear in the output of the show configuration LACP The following commands are set by the example Set LACP static lag.0.9 Set LACP aadminkey lag.0.9 1063 Set port LACP port that.1-2.3 aadminkey 1063 Set port LACP port this.1-2.3 disable Note 2. As with any Cli command issued, the above commands will only appear in the output of a Show configuration Verify the Static LAG status Cli command format: show LACP Example: show LACP lag.0.9 Good Luck Jason

Great, Thanks for the info Erik. A static lag seems the way to go.
GTM-P2G8KFN